Car transfer case Range Rover 3
Draining and filling the working fluid
Dismantling 1. Place the vehicle on a lift. 2. Install a container to collect the leaking working fluid. 3. Unscrew the drain plug and remove the sealing ring. 4. Allow the working fluid to drain....
Dismantling 1. Place the vehicle on a lift. 2. Install a container to collect the leaking working fluid. 3. Unscrew the drain plug and remove the sealing ring. 4. Allow the working fluid to drain....
Removal and installation of the TD6 transfer case
Before disconnecting the battery, make sure that all requirements and conditions contained in the section on disconnecting the battery are met. GENERAL INFORMATION, Precautions when working with...
Before disconnecting the battery, make sure that all requirements and conditions contained in the section on disconnecting the battery are met. GENERAL INFORMATION, Precautions when working with...
Removal and installation a V8 transfer case
Dismantling 1. Place the vehicle on a lift. 2. Disconnect the negative terminal from the battery. 3. Using tools LRT-12-214 and LRT-12-215, loosen the viscous coupling mounting nut and remove it...
Dismantling 1. Place the vehicle on a lift. 2. Disconnect the negative terminal from the battery. 3. Using tools LRT-12-214 and LRT-12-215, loosen the viscous coupling mounting nut and remove it...
Input shaft seal
Dismantling 1. Remove the transfer case. TRANSFER CASE, REPAIR WORK, Transfer case - Td6. TRANSFER CASE, REPAIR WORK, Transfer case - V8. 2. Using a lever, remove the input shaft seal from the...
Dismantling 1. Remove the transfer case. TRANSFER CASE, REPAIR WORK, Transfer case - Td6. TRANSFER CASE, REPAIR WORK, Transfer case - V8. 2. Using a lever, remove the input shaft seal from the...
Front output shaft seal
Dismantling 1. Drain the working fluid from the transfer case. TRANSFER CASE, ADJUSTMENTS, Draining and filling the working fluid. 2. Remove the front propeller shaft. DRIVE SHAFTS, REPAIR WORK,...
Dismantling 1. Drain the working fluid from the transfer case. TRANSFER CASE, ADJUSTMENTS, Draining and filling the working fluid. 2. Remove the front propeller shaft. DRIVE SHAFTS, REPAIR WORK,...
Rear output shaft seal
Dismantling 1. Remove the rear propeller shaft. DRIVE SHAFTS, REPAIR WORK, Cardan shaft - rear. 2. Remove the pin securing the output shaft flange nut. 3. Using the LRT-51-003 tool, hold the shaft...
Dismantling 1. Remove the rear propeller shaft. DRIVE SHAFTS, REPAIR WORK, Cardan shaft - rear. 2. Remove the pin securing the output shaft flange nut. 3. Using the LRT-51-003 tool, hold the shaft...
Transfer case fuse in the electronic control unit
Dismantling 1. Remove the battery tray. ENGINE STARTING AND BATTERY CHARGING SYSTEM, REPAIR WORK, Platform - battery. 2. Release the fasteners securing the electronic control unit cover to the engine...
Dismantling 1. Remove the battery tray. ENGINE STARTING AND BATTERY CHARGING SYSTEM, REPAIR WORK, Platform - battery. 2. Release the fasteners securing the electronic control unit cover to the engine...
Vibration Damper TD6
Dismantling 1. Remove the front propeller shaft. DRIVE SHAFTS, REPAIR WORK, Cardan shaft - front. 2. Remove the 3 Torx screws securing the vibration damper and remove the vibration damper. Assembly...
Dismantling 1. Remove the front propeller shaft. DRIVE SHAFTS, REPAIR WORK, Cardan shaft - front. 2. Remove the 3 Torx screws securing the vibration damper and remove the vibration damper. Assembly...
Transfer case electronic control unit
If the electronic control unit needs to be replaced, connect the Testbook/T4 diagnostic tool and follow the recommended steps before disconnecting the battery. Dismantling 1. Remove the battery tray....
If the electronic control unit needs to be replaced, connect the Testbook/T4 diagnostic tool and follow the recommended steps before disconnecting the battery. Dismantling 1. Remove the battery tray....
Gear ratio control actuator
Dismantling 1. Place the vehicle on a lift and select a low gear in the transfer case (Low Range). 2. Turn off the ignition. 3. With the automatic transmission selector in neutral, make sure there is...
Dismantling 1. Place the vehicle on a lift and select a low gear in the transfer case (Low Range). 2. Turn off the ignition. 3. With the automatic transmission selector in neutral, make sure there is...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections from Land Rover repair manuals:
• Power unit: Transfer case Land Rover Freelander 2 (2006-2014)
• Power unit: Transfer case Land Rover Discovery 3 (2004-2009)
• Power unit: Transfer case Land Rover Defender 2007+ (2007-2016)
• Power unit: Transfer case Land Rover Freelander 2 (2006-2014)
• Power unit: Transfer case Land Rover Discovery 3 (2004-2009)
• Power unit: Transfer case Land Rover Defender 2007+ (2007-2016)