Car front suspension Range Rover 3
Bleeding and filling the air suspension system with air
Bleeding air from the system 1. Bleed the system using the TestBook/T4 diagnostic tool. CAUTION: The maximum air pressure in the air suspension system is: For cars with VIN number up to 106309 -13.7...
Bleeding air from the system 1. Bleed the system using the TestBook/T4 diagnostic tool. CAUTION: The maximum air pressure in the air suspension system is: For cars with VIN number up to 106309 -13.7...
Setting up the air suspension system
The air suspension system must be adjusted after replacing the following components: Electronic control unit of the air suspension system, Body height sensor, Body panels containing mounting points...
The air suspension system must be adjusted after replacing the following components: Electronic control unit of the air suspension system, Body height sensor, Body panels containing mounting points...
Anti-roll bar
Dismantling 1. Remove the protective shield. EXTERIOR PARTS, REPAIR WORK, Engine protection - front. 2. Raise the front of the vehicle and support it with stands. CAUTION: Do not work under a vehicle...
Dismantling 1. Remove the protective shield. EXTERIOR PARTS, REPAIR WORK, Engine protection - front. 2. Raise the front of the vehicle and support it with stands. CAUTION: Do not work under a vehicle...
Anti-roll bar struts
During this procedure, the position of the front wheels should correspond to the straight-line movement of the vehicle. Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a...
During this procedure, the position of the front wheels should correspond to the straight-line movement of the vehicle. Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a...
Lower control arm ball joints
The lower control arm ball joints must be replaced in pairs. Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the...
The lower control arm ball joints must be replaced in pairs. Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the...
Pneumatic elastic element assembly
Do not bleed the air suspension system until the vehicle has been raised. It is not necessary to release air from the entire air suspension system; it is enough to release it only from the circuit of...
Do not bleed the air suspension system until the vehicle has been raised. It is not necessary to release air from the entire air suspension system; it is enough to release it only from the circuit of...
Wheel hub
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with safety stands. 2. Remove the wheel. 3. Remove...
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with safety stands. 2. Remove the wheel. 3. Remove...
Wheel hub bearing
Dismantling 1. Remove the hub assembly. FRONT SUSPENSION, REPAIR WORK, Hub. 2. Unscrew the 3 bolts securing the brake disc protective cover. 3. Using bolts, secure the LRT-60-033/3 pins to the brake...
Dismantling 1. Remove the hub assembly. FRONT SUSPENSION, REPAIR WORK, Hub. 2. Unscrew the 3 bolts securing the brake disc protective cover. 3. Using bolts, secure the LRT-60-033/3 pins to the brake...
Lower arm
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with safety stands. 2. Remove the wheel. 3. Loosen...
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with safety stands. 2. Remove the wheel. 3. Loosen...
Lower arm bushing
Lower arm bushings must be replaced in pairs. Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with...
Lower arm bushings must be replaced in pairs. Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with...
Body height sensor
On vehicles equipped with xenon headlights, the front and rear height sensors, which are located on the right side of the vehicle, are different from those equipped with vehicles with standard...
On vehicles equipped with xenon headlights, the front and rear height sensors, which are located on the right side of the vehicle, are different from those equipped with vehicles with standard...
Transverse steering rod
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with safety stands. 2. Remove the wheel. 3. Loosen...
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported solely by a jack or lift. Always support the vehicle with safety stands. 2. Remove the wheel. 3. Loosen...
Tie rod bushings
Note: Bushings must be replaced in pairs. Dismantling 1. Remove the tie rod. FRONT SUSPENSION, REPAIR WORK, Transverse steering rod. 2. Using tools LRT-60-032/1 and LRT-60-032/2, remove the bushing...
Note: Bushings must be replaced in pairs. Dismantling 1. Remove the tie rod. FRONT SUSPENSION, REPAIR WORK, Transverse steering rod. 2. Using tools LRT-60-032/1 and LRT-60-032/2, remove the bushing...
Receiver
The pressure sensor located in the receiver is not replaceable. It is replaced together with the receiver. When disconnecting a Voss type nipple from any air suspension component, do not remove it...
The pressure sensor located in the receiver is not replaceable. It is replaced together with the receiver. When disconnecting a Voss type nipple from any air suspension component, do not remove it...
Electronic control unit for air suspension
If the electronic control unit needs to be replaced, connect the Testbook/T4 diagnostic tool and perform the appropriate setup procedure before disconnecting the battery. Dismantling 1. Remove the...
If the electronic control unit needs to be replaced, connect the Testbook/T4 diagnostic tool and perform the appropriate setup procedure before disconnecting the battery. Dismantling 1. Remove the...
Compressor unit
When dismantling the compressor unit, there is no need to bleed air from the air suspension system. Dismantling 1. Lift the cover covering the spare wheel. 2. Unscrew the wing nut securing the spare...
When dismantling the compressor unit, there is no need to bleed air from the air suspension system. Dismantling 1. Lift the cover covering the spare wheel. 2. Unscrew the wing nut securing the spare...
Pressure regulator unit
Do not bleed the air suspension system until the vehicle has been raised. When disconnecting a Voss type fitting from any air suspension component, do not remove it from the air hose being...
Do not bleed the air suspension system until the vehicle has been raised. When disconnecting a Voss type fitting from any air suspension component, do not remove it from the air hose being...
Bypass valve
Dismantling 1. Raise the front of the vehicle and support it with stands. 2. Release air from the front suspension air springs. FRONT SUSPENSION, ADJUSTMENTS, Air suspension system - releasing air...
Dismantling 1. Raise the front of the vehicle and support it with stands. 2. Release air from the front suspension air springs. FRONT SUSPENSION, ADJUSTMENTS, Air suspension system - releasing air...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections from Land Rover repair manuals:
• Chassis: Front suspension Land Rover Freelander 1 (1997-2006)
• Chassis: Front axle axles Land Rover Discovery 3 (2004-2009)
• Chassis: Front drive axle Land Rover Defender 2007+ (2007-2016)
• Chassis: Front suspension Land Rover Freelander 1 (1997-2006)
• Chassis: Front axle axles Land Rover Discovery 3 (2004-2009)
• Chassis: Front drive axle Land Rover Defender 2007+ (2007-2016)