K1.8 engine exhaust system Land Rover Freelander 1
Intake pipe — removal and installation
Dismantling 1. Loosen the fasteners securing the gearshift boot to the floor tunnel. 2. Move the boot aside and disconnect the rear oxygen sensor connector. 3. Remove the lower engine guard. EXTERIOR...
Dismantling 1. Loosen the fasteners securing the gearshift boot to the floor tunnel. 2. Move the boot aside and disconnect the rear oxygen sensor connector. 3. Remove the lower engine guard. EXTERIOR...
Middle section of the exhaust system
Dismantling 1. Raise the vehicle on a four-post lift. 2. Loosen the rear section clamp nut and disconnect the rear section from the middle section of the exhaust system. 3. Unscrew the 2 nuts...
Dismantling 1. Raise the vehicle on a four-post lift. 2. Loosen the rear section clamp nut and disconnect the rear section from the middle section of the exhaust system. 3. Unscrew the 2 nuts...
Rear section of the exhaust system
Dismantling 1. Raise the rear of the vehicle. CAUTION: Do not work under a vehicle supported only by a jack. Always support the vehicle with safety stands. 2. Loosen the rear section pipe clamp nut....
Dismantling 1. Raise the rear of the vehicle. CAUTION: Do not work under a vehicle supported only by a jack. Always support the vehicle with safety stands. 2. Loosen the rear section pipe clamp nut....
Replacing the left intake manifold gaskets
Dismantling 1. Disconnect the negative battery terminal. 2. Drain the coolant from the cooling system. COOLING SYSTEM: MODIFICATION K, volume 1.8, ADJUSTMENTS, Draining the coolant, flushing the...
Dismantling 1. Disconnect the negative battery terminal. 2. Drain the coolant from the cooling system. COOLING SYSTEM: MODIFICATION K, volume 1.8, ADJUSTMENTS, Draining the coolant, flushing the...
Exhaust manifold heat shield: without air conditioning
Dismantling 1. Disconnect the negative battery terminal. 2. Unscrew the nut and 2 bolts securing the heat shield. 3. Remove the heat shield. 4. Remove the spacer from the stud. Installation 1....
Dismantling 1. Disconnect the negative battery terminal. 2. Unscrew the nut and 2 bolts securing the heat shield. 3. Remove the heat shield. 4. Remove the spacer from the stud. Installation 1....
Exhaust manifold heat shield: with air conditioning
Dismantling 1. Disconnect the negative battery terminal. 2. Turn the steering wheel all the way to the right. 3. Unscrew the 3 bolts securing the right mudguard panel and remove the panel. 4. Using a...
Dismantling 1. Disconnect the negative battery terminal. 2. Turn the steering wheel all the way to the right. 3. Unscrew the 3 bolts securing the right mudguard panel and remove the panel. 4. Using a...
Exhaust manifold gaskets
Dismantling 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Remove the exhaust manifold heat shield. COLLECTORS AND EXHAUST SYSTEM: MOD. K, volume...
Dismantling 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Remove the exhaust manifold heat shield. COLLECTORS AND EXHAUST SYSTEM: MOD. K, volume...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections from Land Rover repair manuals:
• Power unit: Emission reduction Land Rover Discovery 3 (2004-2009)
• Power unit: Exhaust system V8 Land Rover Range Rover 3 (2001-2012)
• Power unit: Exhaust system Land Rover Defender 2007+ (2007-2016)
• Power unit: Emission reduction Land Rover Discovery 3 (2004-2009)
• Power unit: Exhaust system V8 Land Rover Range Rover 3 (2001-2012)
• Power unit: Exhaust system Land Rover Defender 2007+ (2007-2016)