Car automatic transmission Land Rover Freelander 1
Adjusting the Engine Start Interlock Switch
Adjustment 1. Move the selector lever to the 'N' position. 2. Loosen the 2 bolts securing the lock switch to the gearbox housing. 3. Install the LRT-44-018 tool onto the gear selector lever on the...
Adjustment 1. Move the selector lever to the 'N' position. 2. Loosen the 2 bolts securing the lock switch to the gearbox housing. 3. Install the LRT-44-018 tool onto the gear selector lever on the...
Replacing the working fluid in the box
Operating procedure 1. Place the car on a lift. CAUTION: Use caution when draining hydraulic fluid, which may be very hot. 2. Apply the parking brake and chock the front and rear wheels. 3. Remove...
Operating procedure 1. Place the car on a lift. CAUTION: Use caution when draining hydraulic fluid, which may be very hot. 2. Apply the parking brake and chock the front and rear wheels. 3. Remove...
Adjusting the selector cable
Adjustment 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Unscrew the nut securing the cable end to the selector lever. 3. Move the selector lever...
Adjustment 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Unscrew the nut securing the cable end to the selector lever. 3. Move the selector lever...
Selector housing — removal and installation
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported only by a jack. Always support the vehicle with safety stands. 2. Remove the top floor tunnel trim....
Dismantling 1. Raise the front of the vehicle. CAUTION: Do not work under a vehicle supported only by a jack. Always support the vehicle with safety stands. 2. Remove the top floor tunnel trim....
Selector handle — removal and installation
Dismantling The drawing corresponds to cars produced before May 2004 (later models are similar) 1. Pull the handle up to disengage it from the lever tail. CAUTION: The lever handle may suddenly come...
Dismantling The drawing corresponds to cars produced before May 2004 (later models are similar) 1. Pull the handle up to disengage it from the lever tail. CAUTION: The lever handle may suddenly come...
Selector cable — removal and installation
Dismantling 1. Remove the top floor tunnel trim. INTERIOR TRIM PARTS, REPAIR WORK, Center console - for vehicles up to model year 2004. 2. Disconnect the cable from the selector lever. 3. Remove the...
Dismantling 1. Remove the top floor tunnel trim. INTERIOR TRIM PARTS, REPAIR WORK, Center console - for vehicles up to model year 2004. 2. Disconnect the cable from the selector lever. 3. Remove the...
Selector position indicator: vehicles up to May 2003
Dismantling 1. Release the pointer from the mounting on the selector trim panel. 2. Disconnect the connector from the pointer and remove the pointer. Installation 1. Connect the connector to the...
Dismantling 1. Release the pointer from the mounting on the selector trim panel. 2. Disconnect the connector from the pointer and remove the pointer. Installation 1. Connect the connector to the...
Selector position indicator: vehicles after May 2004
Dismantling 1. Set the selector to the 'Neutral' position and remove the selector handle. CAUTION: The lever handle may suddenly come loose. Be careful not to injure your face when removing the...
Dismantling 1. Set the selector to the 'Neutral' position and remove the selector handle. CAUTION: The lever handle may suddenly come loose. Be careful not to injure your face when removing the...
Engine start interlock switch
Dismantling 1. Release the lock switch connector from the spring clip on the pan and disconnect the connector. 2. Move the selector lever to the 'N' position. 3. Remove the two bolts securing the...
Dismantling 1. Release the lock switch connector from the spring clip on the pan and disconnect the connector. 2. Move the selector lever to the 'N' position. 3. Remove the two bolts securing the...
Control unit (ECU)
Dismantling 1. Loosen 5 screws and remove the cover of the mounting box. 2. Disconnect the 2 latches and remove the control unit from the mounting box. 3. Disconnect the connector from the controller...
Dismantling 1. Loosen 5 screws and remove the cover of the mounting box. 2. Disconnect the 2 latches and remove the control unit from the mounting box. 3. Disconnect the connector from the controller...
Torque converter seal
Dismantling 1. Remove the gearbox. AUTOMATIC TRANSMISSION: JATCO, REPAIR WORK, Transmission: vehicles with KV6 engine. AUTOMATIC TRANSMISSION: JATCO, REPAIR WORK, Transmission: car with Td4 engine....
Dismantling 1. Remove the gearbox. AUTOMATIC TRANSMISSION: JATCO, REPAIR WORK, Transmission: vehicles with KV6 engine. AUTOMATIC TRANSMISSION: JATCO, REPAIR WORK, Transmission: car with Td4 engine....
Gearbox with KV6 engine (engine and gearbox removed)
Dismantling 1. Release the oxygen sensor connector from the bracket on the left valve cover, disconnect the connector. 2. Unscrew the 4 nuts securing the left exhaust manifold to the cylinder head....
Dismantling 1. Release the oxygen sensor connector from the bracket on the left valve cover, disconnect the connector. 2. Unscrew the 4 nuts securing the left exhaust manifold to the cylinder head....
Gearbox: Cars with KV6 engine — removal and installation
Dismantling 1. Secure the hood in a vertical position. 2. Disconnect the negative battery terminal. 3. Remove the engine soundproofing cover. ENGINE KV6 - MODIFICATION K, Camshafts of the left...
Dismantling 1. Secure the hood in a vertical position. 2. Disconnect the negative battery terminal. 3. Remove the engine soundproofing cover. ENGINE KV6 - MODIFICATION K, Camshafts of the left...
Gearbox: car with Td4 engine — removal and installation
Dismantling 1. Disconnect the negative battery terminal. 2. Secure the hood in a vertical position. 3. Remove the air intake hoses. DIESEL ENGINE FUEL SUPPLY SYSTEM, REPAIR WORK, Air intake system...
Dismantling 1. Disconnect the negative battery terminal. 2. Secure the hood in a vertical position. 3. Remove the air intake hoses. DIESEL ENGINE FUEL SUPPLY SYSTEM, REPAIR WORK, Air intake system...
Sealing the bottom of the gearbox
Dismantling 1. Drain the oil from the gearbox. AUTOMATIC TRANSMISSION: JATCO, ADJUSTMENTS, Replacement of working fluid in the box. 2. Remove the working fluid cooling heat exchanger. AUTOMATIC...
Dismantling 1. Drain the oil from the gearbox. AUTOMATIC TRANSMISSION: JATCO, ADJUSTMENTS, Replacement of working fluid in the box. 2. Remove the working fluid cooling heat exchanger. AUTOMATIC...
Blown-Air Cooling Heat Exchanger: Td4 Engine Vehicles
Dismantling 1. Disconnect the negative battery terminal. 2. Remove the front bumper. EXTERIOR PARTS, REPAIR WORK, Front bumper assembly - for cars up to model year 2004. 3. Disconnect the combined...
Dismantling 1. Disconnect the negative battery terminal. 2. Remove the front bumper. EXTERIOR PARTS, REPAIR WORK, Front bumper assembly - for cars up to model year 2004. 3. Disconnect the combined...
Cooling heat exchanger for working fluid: cars with Td4 engine
Dismantling 1. Disconnect the negative battery terminal. 2. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 3. Place a container to collect any leaking...
Dismantling 1. Disconnect the negative battery terminal. 2. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 3. Place a container to collect any leaking...
Cooling Heat Exchanger for Working Fluid: Vehicles with KV6 Engine
Dismantling 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Place a container to collect the leaking liquid. CAUTION: Use caution when draining...
Dismantling 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Place a container to collect the leaking liquid. CAUTION: Use caution when draining...
Cooling fluid heat exchanger hoses
The procedure described applies equally to the supply and return hoses. Dismantling 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Place a container...
The procedure described applies equally to the supply and return hoses. Dismantling 1. Remove the lower engine guard. EXTERIOR PARTS, REPAIR WORK, Lower engine protection shield. 2. Place a container...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections from Land Rover repair manuals:
• Transmission: Automatic gearbox Land Rover Discovery 1 (1989-1998)
• Power unit: Automatic gearbox GM-5L40-E Land Rover Range Rover 3 (2001-2012)
• Transmission: Automatic gearbox Land Rover Discovery 1 (1989-1998)
• Power unit: Automatic gearbox GM-5L40-E Land Rover Range Rover 3 (2001-2012)