Car interior trim Land Rover Freelander 2

Tightening torque specifications
Description Nm lb-ft Torx Head screw for rack trim panel "A" 3 2 Bolts of the airbag shield bracket of the pillar "A" 9 7 Upper Torx Head Bolt for Pillar Trim Panel "B" 25 18 Torx Head Screw for Top...

Pillar trim panel
Removal 1. 2. NOTE: Do not continue disassembly if the component is removed only for access. Installation 1. Install the A-pillar trim panel and tighten the new Torx screw to 3 N·m (2.2 ft·lbs)....

Upper pillar trim panel
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the lower B-pillar trim panel. Refer to procedure: Lower B-Pillar Trim Panel (501-05 Interior Trim, Removal...

Lower pillar trim panel
Removal 1. 2. NOTE: Do not perform further disassembly if the component is removed only for access. Installation 1. Install the elements back in place in reverse order.

C-pillar trim panel
NOTE: The removal procedure description may contain installation steps. Removal 1. Release the lower seat belt anchor. Tightening torque: 40 Nm WARNING: Use a new bolt. 2. Release the rear door seal....

D-pillar trim panel
Removal 1. Remove the spare wheel cover. 2. Remove the cargo compartment threshold trim. 3. Remove the tailgate seal. 4. Remove the cargo compartment luggage rack. 5. Remove the retaining ring in the...

Front door trim panel
Removal 1. Install the handrail cover. 2. Remove the front door trim panel. 3. Remove the threshold lighting lamp. NOTE: Do not continue disassembly if the component is removed only for access. 4....

Rear Door Trim Panel
Removal 1. Disconnect the battery ground cable. Refer to procedure: Specifications (414-00 Charging System - General Information, Specifications). 2. 3. Remove the rear door trim panel. 4. Remove the...

Lifting tailgate trim panel
Removal 1. 2. NOTE: Do not perform further disassembly if the component is removed only for access. Installation 1. When installing, perform the removal procedure in reverse order.

Upper cladding (without hatch)
CAUTION: Make sure the wiring harnesses are correctly positioned. NOTE: If the headliner must be replaced, be sure to install the washer hose and wiring harness in their original locations. Failure...

Upper cladding (with hatch)
CAUTION: Position the wiring harnesses correctly. NOTE: When replacing the headliner, be sure to install the washer hose and wiring harness in their original positions. Failure to follow these...

Engine cover
Removal 1. 2. 3. Tightening torque: 10 Nm 4. Tightening torque: 10 Nm Installation 1. When installing, perform the removal procedure in reverse order.

Front door frame trim panel
Removal 1. 2. NOTE: Do not continue disassembly if the component is removed only for access. Installation 1. Install the elements back in place in reverse order.

Front door trim panel
Removal 1. Remove the lower B-pillar trim panel. Refer to procedure: Lower B-Pillar Trim Panel (501-05 Interior Trim, Removal and Installation). 2. 3. 4. 5. NOTE: Do not perform further disassembly...

Rear side trim panel
Removal 1. 2. Remove the cargo compartment threshold trim. 3. Remove the tailgate seal. 4. 5. 6. Release the rear door seal. 7. 8. Remove the cargo area light (if equipped). 9. Remove the rear side...

Rear side body panel molding
Tightening torque specifications Description Nm lb-ft Rear body outer panel molding fasteners 4 3 Removal 1. Installation 1. To install, perform the removal procedure in reverse order.

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Freelander 2

Freelander 1