Electronic part of the car control Land Rover Freelander 2
Specification of electronic controls
General specification Detail Specifications Engine management system : Manufacturer BOSCH Parameter EDC 15 C2 Camshaft position sensor : Manufacturer Electrifil Parameter Hall effect Crankshaft...
General specification Detail Specifications Engine management system : Manufacturer BOSCH Parameter EDC 15 C2 Camshaft position sensor : Manufacturer Electrifil Parameter Hall effect Crankshaft...
Description and principle of operation
Pos. Spare part number Name 1 - Manifold Absolute Pressure (MAP) Sensor 2 - Fuel temperature sensor 3 - Fuel Rail Pressure Sensor 4 - Nozzle (4 pcs.) 5 - Pressure regulating valve 6 - Fuel pump...
Pos. Spare part number Name 1 - Manifold Absolute Pressure (MAP) Sensor 2 - Fuel temperature sensor 3 - Fuel Rail Pressure Sensor 4 - Nozzle (4 pcs.) 5 - Pressure regulating valve 6 - Fuel pump...
Control scheme
NOTE: A = Rigid connection Pos. Spare part number Name 1 - ECT sensor 2 - 1st gear position switch 3 - CKP sensor 4 - Starter lock switch 5 - MAP sensor 6 - Lower exhaust gas temperature sensor 7 -...
NOTE: A = Rigid connection Pos. Spare part number Name 1 - ECT sensor 2 - 1st gear position switch 3 - CKP sensor 4 - Starter lock switch 5 - MAP sensor 6 - Lower exhaust gas temperature sensor 7 -...
Inspection and verification
CAUTION: Diagnostics by substituting a component from another vehicle is NOT permitted. Substituting control modules does not guarantee confirmation of the fault and, in addition, may cause...
CAUTION: Diagnostics by substituting a component from another vehicle is NOT permitted. Substituting control modules does not guarantee confirmation of the fault and, in addition, may cause...
Table of signs of malfunction
Sign of malfunction Possible reason Operation Engine not starting The crankshaft does not turn The security system/immobilizer is activated Battery Powertrain control unit relay Parking/Neutral...
Sign of malfunction Possible reason Operation Engine not starting The crankshaft does not turn The security system/immobilizer is activated Battery Powertrain control unit relay Parking/Neutral...
DTC Trouble Code Index
NOTE: If a control module or component is suspected and the vehicle is still under manufacturer's warranty, refer to the warranty and procedures manual or determine if a pre-authorization procedure...
NOTE: If a control module or component is suspected and the vehicle is still under manufacturer's warranty, refer to the warranty and procedures manual or determine if a pre-authorization procedure...
Camshaft Position Sensor (CMP)
NOTE: The removal procedure description may contain installation steps. Removal 1. Disconnect the battery ground cable. Refer to procedure: Specifications (414-00 Charging System - General...
NOTE: The removal procedure description may contain installation steps. Removal 1. Disconnect the battery ground cable. Refer to procedure: Specifications (414-00 Charging System - General...
Crankshaft position sensor (CPS)
NOTE: The removal procedure description may contain installation steps. Removal 1. Raise the vehicle. WARNING: Ensure that the vehicle is supported securely. 2. Remove the front wheel. Refer to the...
NOTE: The removal procedure description may contain installation steps. Removal 1. Raise the vehicle. WARNING: Ensure that the vehicle is supported securely. 2. Remove the front wheel. Refer to the...
Engine Coolant Temperature (ECT) Sensor
Removal 1. Remove the air cleaner assembly. Refer to procedure: Air Cleaner (303-12A Intake Air Distribution and Filtration - 3.2L NA - I6, Removal and Installation). 2. Remove the engine trim. Refer...
Removal 1. Remove the air cleaner assembly. Refer to procedure: Air Cleaner (303-12A Intake Air Distribution and Filtration - 3.2L NA - I6, Removal and Installation). 2. Remove the engine trim. Refer...
Manifold Absolute Pressure (MAP) Sensor
Removal 1. 2. Tightening torque: 10 Nm Installation 1. When installing, perform the removal procedure in reverse order.
Removal 1. 2. Tightening torque: 10 Nm Installation 1. When installing, perform the removal procedure in reverse order.
Intake Air Temperature (IAT) sensor
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the cover and disconnect the ground cable from the battery. Refer to procedure: Specifications (414-00...
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the cover and disconnect the ground cable from the battery. Refer to procedure: Specifications (414-00...
Heated Oxygen Sensor (HO2S)
Special tool 310-121 Wrench, H02S WARNING: Use caution when working near hot exhaust system components. Removal 1. Raise and support the vehicle. WARNING: Do not work on or under a vehicle supported...
Special tool 310-121 Wrench, H02S WARNING: Use caution when working near hot exhaust system components. Removal 1. Raise and support the vehicle. WARNING: Do not work on or under a vehicle supported...
Engine Oil Pressure (EOP) Sensor
NOTE: The removal procedure description may contain installation steps. Removal 1. Disconnect the battery ground cable. Refer to procedure: Specifications (414-00 Charging System - General...
NOTE: The removal procedure description may contain installation steps. Removal 1. Disconnect the battery ground cable. Refer to procedure: Specifications (414-00 Charging System - General...
Intake Manifold Runner Control (IMRC)
Removal 1. Remove the engine cover. Refer to procedure: Engine Cover - 2.2L Duratorq - Td4 (501-05 Interior Trim, Removal and Installation). 2. Tightening torque: 10 Nm Installation 1. Install the...
Removal 1. Remove the engine cover. Refer to procedure: Engine Cover - 2.2L Duratorq - Td4 (501-05 Interior Trim, Removal and Installation). 2. Tightening torque: 10 Nm Installation 1. Install the...
Mass Air Flow (MAF) Sensor
Removal 1. Tightening torque: 2 Nm Installation 1. Install the elements back in place in reverse order. 2. If necessary, perform a short drive cycle. Refer to procedure: Powertrain Control Module...
Removal 1. Tightening torque: 2 Nm Installation 1. Install the elements back in place in reverse order. 2. If necessary, perform a short drive cycle. Refer to procedure: Powertrain Control Module...
Crankshaft Position Sensor (CKP) Pulse Wheel
NOTE: The removal procedure descriptions in this manual may contain installation steps. Removal 1. Raise and support the vehicle. WARNING: Ensure that the vehicle is supported securely. 2. Remove the...
NOTE: The removal procedure descriptions in this manual may contain installation steps. Removal 1. Raise and support the vehicle. WARNING: Ensure that the vehicle is supported securely. 2. Remove the...
Engine Control Module (ECM)
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the cover and disconnect the ground cable from the battery. Refer to procedure: Specifications (414-00...
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the cover and disconnect the ground cable from the battery. Refer to procedure: Specifications (414-00...
Fuel temperature sensor
Avoid the presence of open flames, sparks or flammable materials. After stopping the engine, wait at least one minute before performing any repairs to the fuel injection system. Removal 1. Remove the...
Avoid the presence of open flames, sparks or flammable materials. After stopping the engine, wait at least one minute before performing any repairs to the fuel injection system. Removal 1. Remove the...
Oil temperature sensor
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the cover and disconnect the ground cable from the battery. Refer to procedure: Specifications (414-00...
NOTE: The removal procedure description may contain installation steps. Removal 1. Remove the cover and disconnect the ground cable from the battery. Refer to procedure: Specifications (414-00...
Exhaust gas temperature sensor
WARNING: Use caution when working near hot exhaust system components. NOTE: The removal procedure description may contain installation steps. 1. Raise and support the vehicle. WARNING: Do not work...
WARNING: Use caution when working near hot exhaust system components. NOTE: The removal procedure description may contain installation steps. 1. Raise and support the vehicle. WARNING: Do not work...
Diesel Particulate Filter (DPF) Temperature Sensor
WARNING: Use caution when working near hot exhaust system components. NOTE: The removal procedure descriptions in this manual may contain installation steps. 1. Raise and support the vehicle....
WARNING: Use caution when working near hot exhaust system components. NOTE: The removal procedure descriptions in this manual may contain installation steps. 1. Raise and support the vehicle....
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections from Land Rover repair manuals:
• Power unit: Electronic control part Land Rover Discovery 3 (2004-2009)
• Power unit: Electronic parts Land Rover Defender 2007+ (2007-2016)
• Power unit: Electronic control part Land Rover Discovery 3 (2004-2009)
• Power unit: Electronic parts Land Rover Defender 2007+ (2007-2016)