Car Repair Techniques Land Rover Freelander 2
General information on service
This manual contains descriptions and methods for performing adjustments, maintenance and repairs based on proven and effective procedures. Following these procedures will ensure the reliability of...
This manual contains descriptions and methods for performing adjustments, maintenance and repairs based on proven and effective procedures. Following these procedures will ensure the reliability of...
Car at the service station
When working on a vehicle at a service station, the following requirements must always be observed: To prevent the vehicle from moving forward or backward, apply the parking brake or place wheel...
When working on a vehicle at a service station, the following requirements must always be observed: To prevent the vehicle from moving forward or backward, apply the parking brake or place wheel...
Rechargeable battery
Before performing any procedure that involves disconnecting/connecting the battery, refer to the electrical section of this manual entitled "Disconnecting/Connecting the Battery". For additional...
Before performing any procedure that involves disconnecting/connecting the battery, refer to the electrical section of this manual entitled "Disconnecting/Connecting the Battery". For additional...
Towing a car
When towing the vehicle, connect the remote control and turn on the ignition. (The steering lock is unlocked and the signal lights are on.) Only then will the steering, turn signals, horn and brake...
When towing the vehicle, connect the remote control and turn on the ignition. (The steering lock is unlocked and the signal lights are on.) Only then will the steering, turn signals, horn and brake...
General installation instructions
Removal components Before removing a component, clean it and its installation location. Close the holes created when removing the component. After removing the component, immediately seal the ends of...
Removal components Before removing a component, clean it and its installation location. Close the holes created when removing the component. After removing the component, immediately seal the ends of...
Detergents
Always use only cleaning agents that are suitable for the work being performed and the components being cleaned. Do NOT use gasoline as a cleaning (degreasing) agent. Make sure that the component can...
Always use only cleaning agents that are suitable for the work being performed and the components being cleaned. Do NOT use gasoline as a cleaning (degreasing) agent. Make sure that the component can...
General inspection of units
Before reassembly, all components must be carefully inspected for signs of wear and damage. Always ensure that the component being inspected is free of oil and grease. If it is necessary to measure...
Before reassembly, all components must be carefully inspected for signs of wear and damage. Always ensure that the component being inspected is free of oil and grease. If it is necessary to measure...
Joints and butt surfaces
When assembling, mating gaskets must be dry unless otherwise specified. Always apply the specified lubricant to the O-rings and install the O-rings with your fingers only. To remove any remaining old...
When assembling, mating gaskets must be dry unless otherwise specified. Always apply the specified lubricant to the O-rings and install the O-rings with your fingers only. To remove any remaining old...
Locking devices
Always replace locking devices with ones of identical design and size. Lock washers with bending . tabs Always replace the tab washers with new ones when assembling. Do not reuse these lock washers....
Always replace locking devices with ones of identical design and size. Lock washers with bending . tabs Always replace the tab washers with new ones when assembling. Do not reuse these lock washers....
Parts with cylindrical threads
Nuts, bolts and screws with damaged threads must be replaced with new ones. Running a damaged thread with a die or tap leads to weakening of the thread and to an increase in the clearance in the...
Nuts, bolts and screws with damaged threads must be replaced with new ones. Running a damaged thread with a die or tap leads to weakening of the thread and to an increase in the clearance in the...
Designations of bolts and nuts
All bolts or screws with metric ISO threads made of steel and with an outside diameter greater than 6 mm have the ISO M or M designation stamped on the bolt head. In addition to the manufacturer's...
All bolts or screws with metric ISO threads made of steel and with an outside diameter greater than 6 mm have the ISO M or M designation stamped on the bolt head. In addition to the manufacturer's...
Ball and roller bearings
CAUTION: Special tools have been developed for removing most types of bearings; they should be used whenever indicated. To ensure long service life of the units, follow the instructions below when...
CAUTION: Special tools have been developed for removing most types of bearings; they should be used whenever indicated. To ensure long service life of the units, follow the instructions below when...
Hydraulic brake system
WARNING: Do not mix different types of brake fluid. When loosening or tightening brake pipes or brake hose nuts, always use two wrenches. Make sure the hoses are not kinked or knotted. Secure the...
WARNING: Do not mix different types of brake fluid. When loosening or tightening brake pipes or brake hose nuts, always use two wrenches. Make sure the hoses are not kinked or knotted. Secure the...
Flexible pipes and hoses
When removing and installing flexible lines and hoses of the hydraulic system, follow the instructions listed below. This will ensure reliable and long-lasting operation. Before removing hoses or...
When removing and installing flexible lines and hoses of the hydraulic system, follow the instructions listed below. This will ensure reliable and long-lasting operation. Before removing hoses or...
Precautions when working with electrical equipment
The following instructions are intended to ensure safe working conditions and the safety of the electrical and electronic equipment of the vehicle. Equipment Before diagnosing vehicle systems, make...
The following instructions are intended to ensure safe working conditions and the safety of the electrical and electronic equipment of the vehicle. Equipment Before diagnosing vehicle systems, make...
Precautions when handling fuel
The following information contains basic safety precautions when working with fuels, which must be strictly observed. In addition, some safety rules related to the fuel system are given in this...
The following information contains basic safety precautions when working with fuels, which must be strictly observed. In addition, some safety rules related to the fuel system are given in this...
Oil seals
Never install seals that have been improperly stored or show signs of rough handling. Remove old seals with great care to avoid damaging the contact surfaces and seal housing. Before installation,...
Never install seals that have been improperly stored or show signs of rough handling. Remove old seals with great care to avoid damaging the contact surfaces and seal housing. Before installation,...
Safety precautions when working with the SRS
WARNING: Do not install a rear-facing child seat in the front passenger seat. The SRS system contains components that, if handled improperly, may pose a hazard to service personnel. The following...
WARNING: Do not install a rear-facing child seat in the front passenger seat. The SRS system contains components that, if handled improperly, may pose a hazard to service personnel. The following...
Activation of airbags and seat belt pretensioners
WARNING: When activated, parts of the air bag module become hot enough to cause burns. Wait 30 minutes after activation before handling the air bag module. When activating the SRS components, the...
WARNING: When activated, parts of the air bag module become hot enough to cause burns. Wait 30 minutes after activation before handling the air bag module. When activating the SRS components, the...
Replacing SRS components after deployment
The restraint control module (RCM) must be replaced each time an SRS component has deployed. The SRS side impact sensor should be replaced if there is evidence of physical damage or if the RCM has...
The restraint control module (RCM) must be replaced each time an SRS component has deployed. The SRS side impact sensor should be replaced if there is evidence of physical damage or if the RCM has...
Front airbag deployment
CAUTION: If the front airbags have deployed, the following components must be replaced: Driver airbag module Steering wheel Passenger airbag module Instrument panel Additional wires (only if...
CAUTION: If the front airbags have deployed, the following components must be replaced: Driver airbag module Steering wheel Passenger airbag module Instrument panel Additional wires (only if...
Side airbag deployment
CAUTION: If the side airbags have deployed, the following components of the system must be replaced (the components on the side of the vehicle that was impacted must be replaced): Side airbag Any of...
CAUTION: If the side airbags have deployed, the following components of the system must be replaced (the components on the side of the vehicle that was impacted must be replaced): Side airbag Any of...
Curtain airbag modules
CAUTION: If the side curtain airbags have deployed, the following system components must be replaced (the components on the side of the vehicle that was impacted must be replaced): Side curtain...
CAUTION: If the side curtain airbags have deployed, the following system components must be replaced (the components on the side of the vehicle that was impacted must be replaced): Side curtain...
Rear-end car collision
CAUTION: If the seat belt pretensioners deploy during a rear impact, the following components should be replaced: Seat belt pretensioners Front and rear seat belt inertia reels deployed during impact...
CAUTION: If the seat belt pretensioners deploy during a rear impact, the following components should be replaced: Seat belt pretensioners Front and rear seat belt inertia reels deployed during impact...
Precautions when working with the air conditioning system
The air conditioning system contains working fluids and components that, if handled incorrectly, pose a danger to the operating personnel and the environment. The following instructions are intended...
The air conditioning system contains working fluids and components that, if handled incorrectly, pose a danger to the operating personnel and the environment. The following instructions are intended...
Solvents, sealants and adhesives
Solvents WARNING: Always use extreme caution when handling solvents, sealants and adhesives. Some contain chemicals or emit fumes that may be hazardous to your health. Always follow the...
Solvents WARNING: Always use extreme caution when handling solvents, sealants and adhesives. Some contain chemicals or emit fumes that may be hazardous to your health. Always follow the...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections from Land Rover repair manuals:
• General information: Technique Land Rover Discovery 3 (2004-2009)
• General information: Repair techniques Land Rover Range Rover 3 (2001-2012)
• General information: Technique Land Rover Discovery 3 (2004-2009)
• General information: Repair techniques Land Rover Range Rover 3 (2001-2012)