DTC Trouble Code Index (Freelander 2)

NOTE: If a control module or component is suspected and the vehicle remains under manufacturer's warranty, refer to the warranty manual (subsection B1.2) before installing a new module/component, or determine if there is a previously approved special program in effect.

NOTE: Generic scan tools cannot read the codes listed or can only read 5-digit codes. Match the 5 digits from the scan tool with the first 5 digits of the listed 7-digit code to identify the fault (the last 2 digits provide additional information readable by the manufacturer-approved diagnostic system).

NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) with three decimal places of accuracy and a current calibration certificate. When testing resistance, be sure to include the resistance of the DMM leads.

NOTE: Before starting diagnostic programs using Pinpoint tests, check and eliminate basic faults.

NOTE: If DTCs are logged and the fault is not present after performing the Pinpoint tests, an intermittent problem may be the cause. Be sure to check for loose connections and corroded terminals.

DTC	Description	Possible reason	Action
B100A11	Fuel Pump Authorization - Short to Ground	Fuel Pump Authorization Circuit Short to Ground	Refer to the electrical circuit diagrams and check the fuel pump authorization circuit for a short to ground
B100A15	Fuel pump authorization - short circuit to battery + or open circuit	Fuel Pump Authorization Circuit - Short to Battery or Open	Refer to the electrical diagrams and check the fuel pump authorization circuit for a short to battery and an open circuit
B102408	Transponder - signal/message transmission failure on the bus	Transponder - signal/message transmission failure on the bus	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102451	Launch control unit - not programmed	Launch Control Unit - Configuration Not Configured	Reconfigure the launch control unit using the manufacturer approved diagnostic system.
B102481	Launch Control Unit - Invalid Serial Data Received	Invalid serial data received	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102487	Launch Control Unit - No Message	No message	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102496	Launch Control Unit - Internal Element Failure	Internal malfunction	Install a new starting control module. For additional information, refer to: Starter Control Module (303-06B Starting System - 2.2L Duratorq - Td4, Removal and Installation).
B102581	Transponder - Invalid serial data	Invalid serial data received	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102608	Steering Column Lock - Bus Signal/Message Failure	Steering Column Lock - Bus Signal/Message Failure	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102651	Steering column lock - not programmed	Steering Column Lock - Configuration Not Configured	Reconfigure the steering column lock using the manufacturer approved diagnostic system.
B102652	Steering column lock - not activated	Request to provide access to power supply to steering column lock not approved	Check the LIN circuit between the steering column lock and the CJB
B102671	Steering column lock - actuator jammed	Should be generated if SCL fails to reach the locked position and the OK position	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102682	Steering column lock	The steering column lock is not programmed correctly	Install a new steering column lock
B102692	Steering Column Lock - Performance Problems or Incorrect Operation	Microswitch/sensor fault	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102694	Steering column lock - operation not as expected	Status messages are received from SCL when SCL should be turned off	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102696	Steering Column Lock - Internal Component Failure	Internal malfunction	Install a new steering column lock, refer to the new module/component installation note at the top of the DTC Index
B102921	Accelerator pedal sensor signal amplitude below minimum	Accelerator pedal sensor signal ＜ 3% of supply voltage (5V)	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B102922	Accelerator pedal sensor signal amplitude above maximum	Accelerator Pedal Sensor Signal >=97% of supply voltage (5 V)	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B108A23	Start button - signal hangs at low voltage	SW1 and SW2 are always active	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B108B23	Start Button Circuit "A" - Signal Stuck at Low Voltage	SW1 is continuously active for a long time when a button press is registered in SW2	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B108B24	Start Button Circuit "A" - Signal Stuck at High Voltage	SW1 is never active when a press of SW2 is registered	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B108C23	Start Button Circuit "B" - Signal Stuck at Low Voltage	SW2 is continuously active for a long time when a button press is registered in SW1	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B108C24	Start Button Circuit "B" - Signal Stuck at High Voltage	SW2 is never active when a press of SW1 is registered	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B108D24	Start Button Circuit "C" - Signal Stuck at High Voltage	SW3 is never active when a press of SW1 is registered	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B109512	Windscreen wiper on/off relay - short circuit to battery +	Wiper On/Off Relay Electrical Circuit - Short to Battery +	Refer to the electrical diagrams and check the wiper on/off relay circuit for a short to battery +
B109514	Windscreen wiper on/off relay - short to ground or open circuit	Wiper On/Off Relay Electrical Circuit - Short to Ground, Open	Refer to the electrical circuit diagrams and check the wiper on/off relay circuit for a short to ground and an open circuit
B109612	Wiper High/Low Speed Relay - Short to Battery +	Wiper High/Low Speed Relay Circuit Short to Battery	Refer to the electrical diagrams and check the wiper high/low speed relay circuit for a short to battery voltage
B109614	Wiper High/Low Speed Relay - Short to Ground or Open	Wiper High/Low Speed Relay Circuit Short to Ground, Open	Refer to the electrical circuit diagrams and check the high/low speed wiper relay circuit for a short to ground or open circuit
B109712	Windshield heating relay - short circuit to battery +	Windshield Heating Relay Circuit Short to Battery +	Refer to the electrical diagrams and check the heated windshield relay circuit for a short to battery voltage
B109714	Windshield Heater Relay - Short to Ground or Open	Windshield Heater Relay Circuit Short to Ground, Open	Refer to the electrical diagrams and check the heated windshield relay circuit for a short to ground and an open circuit
B109B11	License Plate Light - Short to Ground	License Plate Light Circuit Short to Ground	Refer to the electrical diagrams and check the license plate lamp circuit for a short to ground
B109B13	License plate light - open circuit	License plate light electrical circuit - open circuit	Refer to the electrical diagrams and check the license plate light circuit for an open circuit
B10A202	Collision Input Signal - Total Signal Error	Invalid signal received	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B10A211	Crash Input - Short to Ground	Crash Input Signal Circuit Short to Ground	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B10A215	Crash signal - short circuit to battery + or open circuit	Crash signal circuit - short to battery, open	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B10A268	Collision Signal - Event Information	Collision Signal - Event Information	Check for DTCs for the RCM and refer to the appropriate DTC Index. For additional information, refer to: Supplemental Restraint System (SRS) (501-20B Supplemental Restraint System, Diagnosis and Testing).
B10A512	Alarm system siren - short circuit to battery +	Alarm siren electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the alarm siren circuit for a short to battery +
B10A514	Alarm system siren - short to ground or open circuit	Alarm siren electrical circuit - short to ground, open circuit	Refer to the electrical diagrams and check the alarm siren circuit for a short to ground and an open circuit
B10AC86	Cruise Control Switch - Invalid Signal	Invalid signal	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B10AC87	Cruise Control Switch - No Message	No message	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B10AC95	Cruise Control Switch - Incorrect Assembly	Mismatch between vehicle configuration file and vehicle	Check/update the vehicle configuration file using a manufacturer approved diagnostic system
B10AD04	Rain sensor - internal system failure	Internal sensor failure	Install a new rain sensor. For more information, refer to: Rain Sensor (501-16 Windscreen Wipers and Washers, Removal and Installation).
B10AD09	Rain Sensor - Element Malfunction	Incorrect installation of the rain sensor Internal failure of the rain sensor	Check that the rain sensor is installed correctly. Install a new sensor if necessary. For more information, refer to: Rain Sensor (501-16 Windscreen Wipers and Washers, Removal and Installation).
B10BE11	Solar radiation sensor - short circuit to ground	Solar Radiation Sensor Circuit Short to Ground	Refer to the electrical diagrams and check the solar radiation sensor for a short to ground
B10BE13	Solar radiation sensor - open circuit	Solar radiation sensor electrical circuit - open circuit	Refer to the electrical diagrams and check the solar radiation sensor electrical circuit for an open circuit
B10C012	Fuel pump power supply - short circuit to battery +	Fuel pump power supply circuit - short circuit to battery +	Refer to the electrical diagrams and check the fuel pump power supply circuit for a short to battery +
B10C014	Fuel pump power supply circuit - short to ground, open circuit	Fuel pump power supply circuit - short to ground, open circuit	Refer to the electrical circuit diagrams and check the fuel pump power supply circuit for a short to ground and an open circuit
B10D794	PATS Key - Performance not as expected	No response from transponder in key	Replace the key
B10E511	PCM Wake-up Signal - Short to Ground	Engine Control Module (ECM) Wake-up Signal Circuit Short to Ground	Refer to electrical circuit diagrams and check ECM wake-up signal circuit for short to ground
B10E515	PCM activation signal - short to battery + or open	Engine Control Module (ECM) Wake-up Signal Circuit Short to Battery, Open	Refer to electrical circuit diagrams and check ECM wake-up signal circuit for short to battery and open
B10E712	Ignition relay - short circuit to battery +	Electrical control circuit of power relay with ignition on EJB - short circuit to + battery	Refer to electrical circuit diagrams and check EJB ignition relay control circuit for short to battery +
B10E714	Ignition relay - short to ground or open circuit	EJB ignition on power relay control circuit - short to ground, open	Refer to electrical circuit diagrams and check EJB ignition relay control circuit for short to ground and open circuit
B10EA12	Electric circuit of a heater with a positive temperature coefficient - short circuit on the battery surface	Electric circuit of a heater with a positive temperature coefficient - short circuit on the battery surface	Refer to the electrical diagrams and check the electrical circuit of the heater with a positive temperature coefficient for the presence of a short circuit on the battery surface
B10EA14	PTC heater - short to ground or open circuit	Electric circuit of a heater with a positive temperature coefficient - short circuit to ground, break	Refer to the electrical diagrams and check the PTC heater circuit for a short to ground and an open circuit
B10EB77	Driver's door double locking drive motor - set position not reached	Incorrect feedback signal from DDM	Check for Lost Communication DTCs and perform the appropriate Pinpoint Test using the manufacturer approved diagnostic system. If no Lost Communication DTCs are found, check the door double lock mechanism for a mechanical fault
B10EC77	Passenger door double locking drive motor - set position not reached	Incorrect feedback signal from PDM	Check for Lost Communication DTCs and perform the appropriate Pinpoint Test using the manufacturer approved diagnostic system. If no Lost Communication DTCs are found, check the door double lock mechanism for a mechanical fault
B10ED77	Driver side rear door double locking motor - set position not reached	Incorrect feedback signal from rear door on driver's side	Check for DTCs related to loss of communication with the DDM and perform the appropriate Pinpoint test using the manufacturer approved diagnostic system. If no DTCs related to loss of communication are found, perform the Pinpoint tests related to this DTC using the manufacturer approved diagnostic system and check the door double lock mechanism for a mechanical failure
B10EE77	Rear passenger side double locking motor - set position not reached	Incorrect feedback signal from rear door on passenger side	Check for PDM communication loss DTCs and perform the appropriate Pinpoint test using the manufacturer approved diagnostic system. If no communication loss DTCs are found, perform the Pinpoint tests for that DTC using the manufacturer approved diagnostic system and check the door double lock mechanism for a mechanical failure
B10EF12	Sunroof Speed Output Short to Battery +	Sunroof Speed Signal Output Circuit Short to Battery	Refer to electrical circuit diagrams and check sunroof speed output circuit for short to battery positive
B10EF14	Sunroof Speed Output Signal - Short to Ground or Open	Sunroof Speed Output Circuit Short to Ground, Open	Refer to the electrical circuit diagrams and check the sunroof speed output circuit for a short to ground and an open circuit
B10F212	Sunroof control circuit short to battery +	Sunroof control circuit short to battery +	Refer to the electrical diagrams and check the sunroof control circuit for a short to battery voltage
B10F214	Sunroof Control Circuit Short to Ground or Open	Sunroof control circuit short to ground, open circuit	Refer to the electrical circuit diagrams and check the sunroof control circuit for short to ground and open circuit
B10F311	Left front side light - short circuit to ground	Left Front Parking Light Circuit - Short to Ground	Refer to the electrical circuit diagrams and check the left front parking lamp circuit for a short to ground
B10F411	Right front parking light - short circuit to ground	Right Front Parking Light Circuit - Short to Ground	Refer to the electrical circuit diagrams and check the right front parking lamp circuit for a short to ground
B10F511	Left rear side light - short circuit to ground	Left Rear Parking Light Circuit Short to Ground	Refer to the electrical circuit diagrams and check the left rear position lamp circuit for a short to ground
B10F512	Left rear side light - short circuit to battery +	Left rear side light electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the left rear parking light circuit for a short to battery voltage
B10F611	Right rear side light - short circuit to ground	Right rear parking light circuit - short circuit to ground	Refer to the electrical circuit diagrams and check the right rear parking lamp circuit for a short to ground
B10F612	Right rear side light - short circuit to battery +	Right rear side light electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the right rear parking light circuit for a short to battery voltage
B110112	Comfort function relay - short circuit to battery +	Electrical control circuit for comfort function relay - short circuit to battery +	Refer to the electrical diagrams and check the electrical circuit of the comfort function relay control for a short to battery +
B110114	Comfort function relay - short circuit to ground or open circuit	Comfort function relay control circuit - short circuit to ground, open circuit	Refer to the electrical circuit diagrams and check the comfort function relay control circuit for a short to ground and an open circuit
B110877	Driver's door central locking drive motor - set position not reached	Incorrect feedback signal from DDM	Check for Loss of Communication related DTCs and perform the appropriate Pinpoint Test using the manufacturer approved diagnostic system. If no Loss of Communication related DTCs are found, check the central locking mechanism for a mechanical fault
B110977	Electric motor for the central locking drive of the passenger door - the set position is not reached	Incorrect feedback signal from PDM	Check for Loss of Communication related DTCs and perform the appropriate Pinpoint Test using the manufacturer approved diagnostic system. If no Loss of Communication related DTCs are found, check the central locking mechanism for a mechanical fault
B110A77	Electric motor for the central locking drive of the rear door on the driver's side - the set position is not reached	Incorrect feedback signal from rear door on driver's side	Check for DTCs related to loss of communication with DDM and perform the appropriate Pinpoint test using the manufacturer approved diagnostic system. If no DTCs related to loss of communication are found, perform the Pinpoint tests related to this DTC using the manufacturer approved diagnostic system and check the central locking mechanism for mechanical failure
B110B77	Electric motor for the central locking drive of the rear door on the passenger side - the set position is not reached	Incorrect feedback signal from rear door on passenger side	Check for PDM communication loss related DTCs and perform the appropriate Pinpoint test using the manufacturer approved diagnostic system. If no communication loss related DTCs are found, perform the Pinpoint tests related to this DTC using the manufacturer approved diagnostic system and check the central locking mechanism for a mechanical failure
B111511	High Brake Light Control Circuit Short to Ground	High Brake Light Control Circuit Short to Ground	Refer to electrical circuit diagrams and check high mounted stop lamp control circuit for short to ground
B111513	High mounted brake light control circuit - open circuit	High mounted brake light control circuit - open circuit	Refer to the electrical circuit diagrams and check the high mounted stop lamp control circuit for an open
B112A12	Ignition relay B - short circuit to battery +	Electrical circuit of power relay with ignition on RJB - short circuit to + battery	Refer to the electrical diagrams and check the RJB ignition on power relay circuit for a short to battery +
B112A14	Ignition relay B - short circuit to ground or open circuit	RJB Ignition On Power Relay Circuit Short to Ground, Open	Refer to the electrical circuit diagrams and check the RJB ignition power relay circuit for a short to ground and an open
B112B07	Steering Wheel Module - Mechanical Faults	Any position or button on the windshield wiper lever is active for more than 60 seconds (180 seconds for cruise control buttons) Internal switch failure	Check for a sticking windshield wiper or cruise control switch. Install a new switch if necessary. For more information, refer to: Multifunction Steering Column Switch (211-05 Steering Column Switches, Removal and Installation).
B112B88	Steering Wheel Module - Bus Disabled	Lost Communication with Steering Wheel Module	Perform the diagnostic procedure for this DTC using the manufacturer approved diagnostic system
B112C88	Interior Motion Sensor - Bus Disabled	Lost connection with the interior motion sensor	Perform the diagnostic procedure for this DTC using the manufacturer approved diagnostic system
B113007	Light Switch Module - Mechanical Faults	Any buttons on the light switch module are active for more than 60 seconds or the exterior light switch is in an illegal combination Internal switch failure	Check for sticking of the light switch button. Install a new light switch if necessary. For more information, refer to: Headlight Switch (417-01 Exterior Lighting, Removal and Installation).
B113088	Light Switch Module - Bus Disabled	Lost Communication with Light Switch Module	Perform the diagnostic procedure for this DTC using the manufacturer approved diagnostic system
B113188	Wiper Motor Module - Bus Disabled	Lost Communication with Windshield Wiper Motor Module	Perform the diagnostic procedure for this DTC using the manufacturer approved diagnostic system
B113C11	Hazard warning light switch illumination circuit - short to ground	Hazard warning light switch illumination circuit - short to ground	Refer to the electrical circuit diagrams and check the hazard warning switch illumination circuit for a short to ground
B113C15	Hazard warning light button illumination - short circuit to battery + or open circuit	Electrical circuit of the hazard warning light button illumination - short circuit to + battery, open circuit	Refer to the electrical diagrams and check the hazard warning light switch illumination circuit for short to battery and open circuit
B113D12	Sunroof master open/close control mechanism - short circuit to battery +	Sunroof Panel Master Open/Close Control Circuit - Short to Battery +	Refer to electrical circuit diagrams and check sunroof master open/close control circuit for short to battery positive
B113D14	Sunroof General Open/Close Control Circuit - Short to Battery +	Sunroof Panel Master Open/Close Control Circuit - Short to Ground, Open	Refer to electrical circuit diagrams and check sunroof master open/close control circuit for short to ground and open
B118251	Tire Pressure Monitoring System (TPMS) - Not Programmed	TPMS module in transport mode/factory mode	Enter the TPMS module into user mode using the manufacturer approved diagnostic system
B11BC11	Additional Accessories Relay Circuit Short to Ground	Additional Accessories Relay Circuit Short to Ground	Refer to the electrical diagrams and check the accessory relay circuit for a short to ground
B11BC15	Additional Accessories Relay Circuit - Short to Battery +, Open	Additional Accessories Relay Circuit - Short to Battery +, Open	Refer to the electrical diagrams and check the accessory relay circuit for short to battery + and open circuit
B1A7911	Rear fog lamp circuit short to ground	Rear fog lamp power supply circuit - short circuit to ground	Refer to the electrical circuit diagrams and check the rear fog lamp power supply circuit for a short to ground
B1A7913	Rear fog light electrical circuit - open circuit	Rear fog light power supply circuit - open circuit	Refer to the electrical diagrams and check the rear fog lamp power supply circuit for an open circuit
B1A8441	Vehicle Configuration Data - General Checksum Error	Checksum error	Configure the CJB as a new unit using the manufacturer approved diagnostic system
B1A9904	Power On Reset - Internal System Fault	A DTC will be generated if the reset counter reaches its maximum value (currently 5)	Install a new CJB, refer to the new module/component installation note at the top of the DTC Index
B1C9611	Alarm indicator circuit short to ground	Alarm indicator circuit short to ground	Refer to the electrical diagrams and check the alarm indicator circuit for a short to ground
B1C9615	Alarm indicator electrical circuit - short circuit to battery +, open circuit	Alarm indicator electrical circuit - short circuit to battery +, open circuit	Refer to the electrical diagrams and check the alarm indicator circuit for a short to battery and an open circuit
B1D0011	Left Low Beam Headlamp Circuit Short to Ground	Left Low Beam Headlamp Circuit Short to Ground	Refer to the electrical circuit diagrams and check the left low beam headlamp circuit for a short to ground
B1D0013	Left low beam headlight electrical circuit - open circuit	Left low beam headlight electrical circuit - open circuit	Refer to the electrical diagrams and check the left low beam headlamp circuit for an open circuit
B1D0111	Right Low Beam Headlamp Circuit Short to Ground	Right Low Beam Headlamp Circuit Short to Ground	Refer to the electrical circuit diagrams and check the right low beam headlamp circuit for a short to ground
B1D0113	Right low beam headlight circuit - open circuit	Right low beam headlight circuit - open circuit	Refer to the electrical diagrams and check the right low beam headlamp circuit for an open circuit
B1D0611	Left turn signal circuit short to ground	Left turn signal circuit short to ground	Refer to the electrical diagrams and check the left turn signal circuit for a short to ground
B1D0613	Left turn signal electrical circuit - open circuit	Left turn signal electrical circuit - open circuit	Refer to the electrical diagrams and check the left turn signal circuit for an open
B1D0711	Right turn signal circuit short to ground	Right turn signal circuit short to ground	Refer to the electrical diagrams and check the right turn signal circuit for a short to ground
B1D0713	Right turn signal electrical circuit - open circuit	Right turn signal electrical circuit - open circuit	Refer to the electrical diagrams and check the right turn signal circuit for an open
B1D1700	Self-powered siren - General information about faults	Internal tilt sensor failure	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
B1D1788	Self-powered siren - bus off	Lost connection with self-powered siren.	Perform the network test associated with this DTC using the manufacturer approved diagnostic system.
B1D1796	Self-powered siren - internal component failure	Self-powered siren - internal fault	Install a new siren with independent power supply. For more information, refer to: Sound signal of the anti-theft alarm with built-in battery (419-01A Anti-theft system - active, Removal and installation).
B1D1896	Volumetric Control Sensor Electrical Circuit - Internal Element Failure	Interior Motion Sensor - Internal Malfunction	Install a new motion sensor in the cabin
B1D2162	Remote Control Switch - Signal Matching Failure	A request was received from the remote control programmable key and the variable code counter reading was incorrect	Set up the key synchronization with the remote control function using the key to start the car
B1C5512	Horn relay coil electrical circuit - short circuit to battery +	Horn relay control circuit - short circuit to battery +	Refer to the electrical diagrams and check the horn relay control circuit for a short to battery +
B1C5514	Horn Relay Coil Circuit Short to Ground or Open	Horn Relay Control Circuit - Short to Ground, Open	Refer to the electrical circuit diagrams and check the horn relay control circuit for a short to ground and an open circuit
B1C8212	Headlamp Washer Relay Coil Circuit Short to Battery +	Headlamp Washer Relay Control Circuit - Short to Battery +	Refer to the electrical diagrams and check the headlamp washer relay control circuit for a short to battery voltage
B1C8214	Headlamp Washer Relay Coil Circuit Short to Ground or Open	Headlamp Washer Relay Control Circuit - Short to Ground, Open	Refer to the electrical circuit diagrams and check the headlamp washer relay control circuit for a short to ground and an open circuit
B1C8412	Rear Window Defogger Relay Output Circuit Short to Battery +	Rear Window Defogger Relay Control Circuit Short to Battery +	Refer to the electrical circuit diagrams and check the rear window defroster relay control circuit for a short to battery voltage
B1C8414	Rear Window Defogger Relay Output Circuit Short to Ground or Open	Rear Window Defogger Relay Control Circuit Short to Ground, Open	Refer to the electrical circuit diagrams and check the rear window defroster relay control circuit for a short to ground and an open circuit
B1C9012	Additional high beam headlights relay coil electrical circuit - short circuit to battery +	Additional high beam headlights relay control circuit - short circuit to battery +	Refer to the electrical circuit diagrams and check the auxiliary high beam relay control circuit for a short to battery voltage
B1C9014	Additional high beam headlight relay coil circuit - short to ground or open	Additional high beam headlights relay control circuit - short circuit to ground, open circuit	Refer to the electrical circuit diagrams and check the auxiliary high beam relay control circuit for a short to ground and an open circuit
B1D1312	Interior Light Circuit No.1 - Short to Battery +	Instrument cluster illumination electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the instrument panel illumination circuit for a short to battery +
B1D1314	Interior Light Circuit #1 Short to Ground or Open	Instrument cluster illumination circuit - short to ground, open circuit	Refer to the electrical diagrams and check the instrument cluster illumination circuit for a short to ground and an open circuit
B1D1A12	Interior Light Circuit 'C' Short to Battery +	Ceiling console lighting electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the ceiling light electrical circuit for a short to battery +
B1D1A14	Interior lamps 'C' circuit short to ground or open	Ceiling console light circuit - short to ground, open	Refer to the electrical diagrams and check the ceiling light circuit for a short to ground and an open circuit
B1D3524	Hazard Light Button - Signal Stuck at High Voltage	The hazard warning light switch has been pressed for more than 60 seconds	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
C002311	Brake Light Control Circuit Short to Ground	Brake Light Control Circuit Short to Ground	Refer to the electrical circuit diagrams and check the brake light control circuit for a short to ground
C002313	Brake light control circuit - open circuit	Brake light control circuit - open circuit	Refer to the electrical diagrams and check the brake light control circuit for an open
C110811	Electrical circuit of supply voltage of sensor(s) of pedal(s) - short circuit to ground	Electrical circuit of supply voltage of sensor(s) of pedal(s) - short circuit to ground	Refer to electrical circuit diagrams and check the pedal sensor(s) supply voltage circuit for a short to ground
C110815	Supply voltage of pedal sensor(s) - short circuit to + battery or open circuit	Electric circuit of supply voltage of sensor(s) of pedal(s) - short circuit to + battery, open circuit	Refer to the electrical diagrams and check the pedal sensor(s) supply voltage circuit for short to battery and open circuit
C1A4121	Clutch pedal sensor signal amplitude below minimum	signal < 3% of supply voltage (5V)	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
C1A4122	Clutch pedal sensor signal amplitude above maximum	signal>=97% of supply voltage (5V)	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
C1A5616	Left Front Wheel Module - Circuit Voltage Below Threshold (Low Battery Voltage)	Siemens internal algorithm	Install a new module if necessary.
C1A5686	Left Front Wheel Module - Invalid Signal (Out of Range)	Siemens internal algorithm	Install a new module if necessary.
C1A5693	Left Front Wheel Module - Not Working (Lost Sensor)	Siemens internal algorithm	Install a new module if necessary.
C1A5711	Left Front Wheel Actuator - Short to Ground	Left Front Wheel Actuator Circuit Short to Ground	Refer to the electrical circuit diagrams and check the left front wheel actuator circuit for a short to ground
C1A5712	Left Front Wheel Actuator - Short to Battery +	Left Front Wheel Actuator Electrical Circuit - Short to Battery +	Refer to the electrical diagrams and check the left front wheel actuator circuit for a short to battery +
C1A5713	Left Front Wheel Actuator Circuit - Open	Left Front Wheel Actuator Circuit - Open	Refer to the electrical diagrams and check the left front wheel actuator circuit for an open circuit
C1A5816	Right Front Wheel Module - Electrical Circuit Voltage Below Threshold (Low Battery Voltage)	Siemens internal algorithm	Install a new module if necessary.
C1A5886	Right Front Wheel Module - Invalid Signal (Out of Range)	Siemens internal algorithm	Install a new module if necessary.
C1A5893	Right Front Wheel Module - Not Working (Lost Sensor)	Siemens internal algorithm	Install a new module if necessary.
C1A5911	Right Front Wheel Actuator - Short to Ground	Right Front Wheel Actuator Circuit Short to Ground	Refer to the electrical circuit diagrams and check the right front wheel actuator circuit for a short to ground
C1A5912	Right Front Wheel Actuator - Short to Battery +	Right Front Wheel Actuator Electrical Circuit - Short to Battery +	Refer to the electrical diagrams and check the right front wheel actuator circuit for a short to battery +
C1A5913	Right Front Wheel Actuator Circuit - Open	Right Front Wheel Actuator Circuit - Open	Refer to the electrical diagrams and check the right front wheel actuator circuit for an open circuit
C1A6016	Left rear wheel module - voltage in electrical circuit below threshold (low battery voltage)	Siemens internal algorithm	Install a new module if necessary.
C1A6086	Left Rear Wheel Module - Invalid Signal (Out of Range)	Siemens internal algorithm	Install a new module if necessary.
C1A6093	Left rear wheel module - not working (sensor lost)	Siemens internal algorithm	Install a new module if necessary.
C1A6111	Left Rear Wheel Actuator - Short to Ground	Left Rear Wheel Actuator Circuit Short to Ground	Refer to the electrical circuit diagrams and check the right front wheel actuator circuit for a short to ground
C1A6112	Left rear wheel actuator - short circuit to battery +	Left rear wheel actuator electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the right front wheel actuator circuit for a short to battery +
C1A6113	Left rear wheel actuator electrical circuit - open	Left rear wheel actuator electrical circuit - open	Refer to the electrical diagrams and check the left rear wheel actuator circuit for an open circuit
C1A6216	Right Rear Wheel Module - Electrical Circuit Voltage Below Threshold (Low Battery Voltage)	Siemens internal algorithm	Install a new module if necessary.
C1A6286	Right Rear Wheel Module - Invalid Signal (Out of Range)	Siemens internal algorithm	Install a new module if necessary.
C1A6293	Right rear wheel module - not working (sensor lost)	Siemens internal algorithm	Install a new module if necessary.
C1A6311	Right Rear Wheel Actuator - Short to Ground	Right Rear Wheel Actuator Circuit Short to Ground	Refer to the electrical circuit diagrams and check the right rear wheel actuator circuit for a short to ground
C1A6312	Right rear wheel actuator - short circuit to battery +	Right rear wheel actuator electrical circuit - short circuit to battery +	Refer to the electrical diagrams and check the right rear wheel actuator circuit for a short to battery +
C1A6313	Right rear wheel actuator electrical circuit - open	Right rear wheel actuator electrical circuit - open	Refer to the electrical diagrams and check the right rear wheel actuator circuit for an open circuit
C1B1412	Sensor power supply circuit #1 short circuit to battery +	Sensor power supply circuit #1 short circuit to battery +	Refer to the electrical diagrams and check the sensor power supply circuit #1 for a short to battery +
C1D1800	Localization failure	Tire Pressure Monitoring Function Signal Localization Failure	Check for additional related DTCs and refer to this DTC Index.
C1D2105	Wheel Module - General Signal Failure	Siemens internal algorithm	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
C1D2249	Right Steering Wheel Switch Module - Internal Malfunction	Right Steering Wheel Switch Module - Internal Malfunction	Install a new washer/wiper switch. For more information, refer to: Steering Column Multifunction Switch (211-05 Steering Column Switches, Removal and Installation).
C200307	Left Steering Wheel Switch Module - Mechanical Faults	Left Steering Wheel Switch Module - Mechanical Failure	Install a new turn signal switch. For more information, refer to: Multifunction Steering Column Sensor (211-05 Steering Column Switches, Removal and Installation).
C200349	Left Steering Wheel Switch Module - Internal Malfunction	Left Steering Wheel Switch Module - Internal Malfunction	Install a new turn signal switch. For more information, refer to: Multifunction Steering Column Sensor (211-05 Steering Column Switches, Removal and Installation).
C200412	Headlamp Washer Relay B Circuit Short to Battery +	Headlamp Washer Relay B Circuit Short to Battery +	Refer to the electrical diagrams and check the headlamp washer relay B circuit for a short to battery
C200414	Headlamp Washer Relay B Circuit Short to Ground, Open	Headlamp Washer Relay B Circuit Short to Ground, Open	Refer to the electrical circuit diagrams and check the headlamp washer relay B circuit for a short to ground and an open circuit
P046015	Fuel level sensor A - short circuit to battery + or open circuit	Sensor input signal > 90% of the sensor supply voltage (5V)	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
P046200	Fuel Level Sensor A Circuit Low Input Voltage	Sensor input signal < 10% of the sensor supply voltage (5V)	Refer to electrical circuit diagrams and check fuel level sensor A circuit for short to ground
P060400	Internal Control Module Direct Access Memory (RAM) Error	Incorrect RAM checksum	Install a new CJB, refer to the new module/component installation note at the top of the DTC Index
P060500	Internal Control Module Read Only Memory (ROM) Error	Incorrect ROM checksum	Install a new CJB, refer to the new module/component installation note at the top of the DTC Index
P062F00	Internal Control Module Read Only Memory (ROM) Error	EEP control value does not match primary value	Install a new CJB, refer to the new module/component installation note at the top of the DTC Index
P080111	Reverse Lock Control Circuit Short to Ground	Reverse Lock Control Circuit Short to Ground	Refer to the electrical circuit diagrams and check the reverse lock control circuit for a short to ground
P134613	Fuel Level Sensor B Circuit - Open	Sensor input signal > 90% of the sensor supply voltage (5V)	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
P134800	Fuel Level Sensor B Circuit Low Input Voltage	Sensor input signal < 10% of the sensor supply voltage (5V)	Refer to electrical circuit diagrams and check fuel level sensor B circuit for short to ground
P167400	The control module software is damaged	Software validation failure inside module	Download the latest software version using the manufacturer's approved diagnostic system
U000100	High-speed CAN bus	The bus is disconnected	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U001000	Medium speed CAN bus	The bus is disconnected	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U010000	Lost Communication with ECM/PCM "A"	Lost communication with ECM	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U010100	Lost connection with TCM	Lost connection with TCM	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U010400	Lost Communication with Cruise Control Module	Lost Communication with Cruise Control Module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U012600	Lost Communication with Steering Angle Sensor Module	Lost connection with steering wheel angle sensor	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U012900	Lost Communication with Brake Control Module	Lost communication with ABS module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U013500	Lost Communication With Front Differential Control Module	Lost Communication with Differential Control Module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U015500	Lost Communication with Instrument Panel Control (IPC) Module	Lost connection with instrument cluster	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U015600	Lost contact with information center "A"	Lost connection with the information center	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U015900	Lost Communication With Parking Assist Control Module 'A'	Lost communication with parking assistance module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U016400	Lost Communication with HVAC (Heating, Ventilation, Air Conditioning) Control Module	Lost communication with the climate control module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U016600	Lost communication with auxiliary heater control module	Lost communication with auxiliary heater control module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U018100	Lost Communication with Headlight Leveling Control Module	Lost Communication with Headlight Leveling Control Module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U019900	Lost communication with door control module "A"	Lost Communication with Driver Door Module (DDM)	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U020000	Lost Communication with Door Control Module "B"	Lost Communication with Passenger Door Module (PDM)	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U020800	Lost Communication With Seat Control Module "A"	Lost Communication with Passenger Seat Module (PSM)	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U021400	Lost connection with remote function activation drive	Lost Communication with Remote Keyless Entry Module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U023100	Lost connection with rain perception module	Lost connection with rain perception module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U023600	Lost Communication with Steering Column Lock Module	Lost Communication with Steering Column Lock Module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U025200	Lost Communication with Rear Lighting Control Module 'B'	Lost connection with trailer module	Perform the appropriate network test for this DTC using the manufacturer approved diagnostic system.
U030100	Software incompatibility with ECM/PCM	ECM is disconnected Incorrect ECM installed	Check the ECM electrical connections. Check if the correct ECM is installed
U040100	Invalid data received from ECM/PCM	Invalid data received from ECM	Check the ECM for DTCs and refer to the DTC Index. For additional information, refer to: Electronic Controls (303-14A Electronic Controls - 3.2L NA - I6, Diagnostics and Testing).
U040500	Invalid data received from cruise control module	Invalid data received from cruise control module	Check the cruise control module for DTCs and refer to the DTC Index. For additional information, refer to: Speed Control (310-03A Speed Control - 3.2L NA - I6, Diagnostics and Testing).
U051500	Invalid data received from remote function activation actuator	Invalid data received from keyless entry module	Check the keyless entry module for DTCs and refer to the DTC Index. Perform the pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
U200562	Vehicle Speed - Signal Comparison Error	Vehicle Speed - Signal Comparison Error	Check ABS for DTCs and refer to DTC Index. For additional information, refer to: Anti-lock Brake System - Yaw Control Function (206-09C Anti-lock Brake System - Yaw Control Function, Diagnosis and Testing).
U201011	Switch illumination circuit short to ground	Switch illumination circuit short to ground	Refer to the electrical diagrams and check the hazard warning light switch circuit for a short to ground
U201015	Switch illumination - short circuit to battery + or open circuit	Switch illumination electrical circuit - short circuit to battery +, open circuit	Refer to the electrical diagrams and check the switch illumination electrical circuit for a short to battery + and an open circuit
U201741	Control Module Software #2 - General Checksum Error	Invalid signal configuration checksum	Install the latest software version using the manufacturer's approved diagnostic system
U201841	Control Module Software #3 - General Checksum Error	Invalid local configuration checksum	Install the latest software version using the manufacturer's approved diagnostic system
U210100	Incompatible control module configuration	Each function logs if a vehicle configuration parameter has a value that is unknown	Check and download the vehicle configuration file
U300051	Control module - not programmed	Vehicle configuration or local configuration or signal configuration files not loaded	Install the latest software version using the manufacturer's approved diagnostic system
U300316	Battery voltage	The voltage in the electrical circuit is below the threshold value	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.
U300317	Battery voltage	The voltage in the electrical circuit is above the threshold value	Perform the Pinpoint tests associated with this DTC using the manufacturer approved diagnostic system.