Restraints Control Module (RCM) Trouble Code (Freelander 2)

Passive safety system control unit

NOTE: If a module or component failure is suspected and the vehicle remains under manufacturer's warranty, refer to the Warranty Guide (Section B1.2) or determine if there is a previously approved special program in effect before replacing the component.

NOTE: Generic scan tools may not be able to read the codes listed or may only be able to read 5-digit codes. Match the 5 digits from the scan tool with the first 5 digits of the listed 7-digit code to identify the fault (the last 2 digits provide additional information readable by the manufacturer-approved diagnostic system).

NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) with three decimal places of accuracy and a valid calibration certificate. When testing resistance, be sure to include the resistance of the DMM leads.

NOTE: Before starting diagnostic programs using fault location tests, check and correct basic faults.

NOTE: Inspect the connectors for signs of water ingress and their pins for damage and/or corrosion.

NOTE: If DTCs are set and the fault is not present after performing the troubleshooting tests, an intermittent problem may be the cause. Be sure to check for loose connections and corroded terminals.

Description and operation

A detailed description of the passive restraint control system is contained in the corresponding section of the repair manual, Description and Operation. For additional information, refer to the chapter: (501-20B Supplemental Restraint System

DTC	Description	Possible reason	Action
B0001-11	Driver's front airbag stage 1 deployment control	Driver Frontal Air Bag Stage 1 Circuit Short to Ground	Using the electrical circuit diagrams, check the driver frontal airbag stage 1 circuit for a short to ground
B0001-12	Driver's front airbag stage 1 deployment control	Electrical circuit of the 1st stage of the front driver's airbag: short circuit to power supply	Using the electrical circuit diagrams, check the driver frontal airbag stage 1 circuit for a short to power
B0001-13	Driver's front airbag stage 1 deployment control	Driver frontal airbag stage 1 circuit: open circuit	Using the electrical diagrams, check the driver's frontal airbag stage 1 circuit for an open
B0001-19	Driver's front airbag stage 1 deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0001-1A	Driver's front airbag stage 1 deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0001-95	Driver's front airbag stage 1 deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0002-11	Driver's front airbag stage 2 deployment control	Driver Frontal Airbag Stage 2 Circuit Short to Ground	Using the electrical circuit diagrams, check the driver's frontal airbag stage 2 circuit for a short to ground
B0002-12	Driver's front airbag stage 2 deployment control	Electrical circuit of the front driver's airbag stage 2: short circuit to power supply	Using the electrical circuit diagrams, check the driver's frontal airbag stage 2 circuit for a short to power
B0002-13	Driver's front airbag stage 2 deployment control	Driver Frontal Airbag Stage 2 Electrical Circuit: Open Circuit	Using the electrical diagrams, check the driver's frontal airbag stage 2 circuit for an open
B0002-19	Driver's front airbag stage 2 deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0002-1A	Driver's front airbag stage 2 deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0002-95	Driver's front airbag stage 2 deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0004-11	Driver knee bolster deployment control circuit	Driver's knee bolster: short circuit to ground	Using the electrical diagrams, check the driver's knee bolster circuit for a short to ground
B0004-12	Driver knee bolster deployment control circuit	Driver's knee bolster: short circuit to power	Using the electrical diagrams, check the driver's knee bolster circuit for a short to power
B0004-13	Driver knee bolster deployment control circuit	Driver's knee bolster: chain break	Using the electrical diagrams, check the driver's knee bolster circuit for an open
B0004-19	Driver knee bolster deployment control circuit	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0004-1A	Driver knee bolster deployment control circuit	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B000495	Driver knee bolster deployment control circuit	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0005-11	Control of the operation of the deformable steering column	Adaptive steering column electrical circuit: short circuit to ground	Using the electrical diagrams, check the adaptive steering column circuit for a short to ground
B0005-12	Control of the operation of the deformable steering column	Adaptive steering column electrical circuit: short circuit to power	Using the electrical diagrams, check the adaptive steering column circuit for a short to power
B0005-13	Control of the operation of the deformable steering column	Adaptive steering column electrical circuit: open circuit	Using the electrical diagrams, check the adaptive steering column circuit for an open
B0005-19	Control of the operation of the deformable steering column	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0005-1A	Control of the operation of the deformable steering column	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0005-95	Control of the operation of the deformable steering column	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0010-11	Control of deployment of the 1st stage of the front passenger airbag	Electrical circuit of the front passenger airbag stage 1: ground short circuit	Using the electrical circuit diagrams, check the front passenger airbag stage 1 circuit for a short to ground
B0010-12	Control of deployment of the 1st stage of the front passenger airbag	Electrical circuit of the front passenger airbag stage 1: power short circuit	Using the electrical circuit diagrams, check the front passenger airbag stage 1 circuit for a short to power
B0010-13	Control of deployment of the 1st stage of the front passenger airbag	Front passenger airbag stage 1 circuit: open circuit	Using the electrical diagrams, check the passenger frontal airbag stage 1 circuit for an open
B0010-19	Control of deployment of the 1st stage of the front passenger airbag	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0010-1A	Control of deployment of the 1st stage of the front passenger airbag	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0010-95	Control of deployment of the 1st stage of the front passenger airbag	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0011-11	Front passenger airbag stage 2 deployment control	Electrical circuit of the front passenger airbag stage 2: ground short circuit	Using the electrical circuit diagrams, check the front passenger airbag stage 2 circuit for a short to ground
B0011-12	Front passenger airbag stage 2 deployment control	Electrical circuit of the front passenger airbag stage 2: power short circuit	Using the electrical circuit diagrams, check the front passenger airbag stage 2 circuit for a short to power
B0011-13	Front passenger airbag stage 2 deployment control	Front passenger airbag stage 2 electrical circuit: open circuit	Using the electrical diagrams, check the passenger frontal airbag stage 2 circuit for an open
B0011-19	Front passenger airbag stage 2 deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0011-1A	Front passenger airbag stage 2 deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0011-95	Front passenger airbag stage 2 deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0050-11	Driver seat belt sensor	Short circuit to ground in the electrical circuit of the driver's seat belt buckle sensor	Using the electrical diagrams, check the driver's seat belt buckle switch circuit for a short to ground
B0050-12	Driver seat belt sensor	Short circuit to power supply of the electrical circuit of the driver's seat belt buckle sensor	Using the electrical diagrams, check the driver's seat belt buckle switch circuit for a short to power
B0050-13	Driver seat belt sensor	Driver's seat belt buckle sensor circuit open	Using the electrical diagrams, check the driver's seat belt buckle switch circuit for an open
B0050-19	Driver seat belt sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0050-1E	Driver seat belt sensor	Electrical circuit resistance is out of acceptable range	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0050-95	Driver seat belt sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0052-11	Passenger seat belt sensor	Short circuit to ground in the electrical circuit of the passenger seat belt buckle sensor	Using the electrical diagrams, check the passenger seat belt buckle switch circuit for a short to ground
B0052-12	Passenger seat belt sensor	Short circuit to power supply of the passenger seat belt buckle sensor circuit	Using the electrical diagrams, check the passenger seat belt buckle switch circuit for a short to power
B0052-13	Passenger seat belt sensor	Open circuit of the passenger seat belt buckle sensor	Using the electrical diagrams, check the passenger seat belt buckle switch circuit for an open
B0052-19	Passenger seat belt sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0052-1E	Passenger seat belt sensor	Electrical circuit resistance is out of acceptable range	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0052-95	Passenger seat belt sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0070-11	Driver's seat belt pretensioner activation control	Driver Seat Belt Pretensioner Circuit Short to Ground	Using the electrical circuit diagrams, check the driver's seat belt pretensioner circuit for a short to ground
B0070-12	Driver's seat belt pretensioner activation control	Driver Seat Belt Pretensioner Circuit Short to Power	Using the electrical circuit diagrams, check the driver's seat belt pretensioner circuit for a short to power
B0070-13	Driver's seat belt pretensioner activation control	Driver's seat belt pretensioner circuit open	Using the electrical diagrams, check the driver's seat belt pretensioner circuit for an open
B0070-19	Driver's seat belt pretensioner activation control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0070-1A	Driver's seat belt pretensioner activation control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0070-95	Driver's seat belt pretensioner activation control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0072-11	Passenger seat belt pretensioner activation control	Passenger Seat Belt Pretensioner Circuit Short to Ground	Using the electrical circuit diagrams, check the passenger seat belt pretensioner circuit for a short to ground
B0072-12	Passenger seat belt pretensioner activation control	Front passenger seat belt pretensioner circuit short to power	Using the electrical circuit diagrams, check the passenger seat belt pretensioner circuit for a short to power
B0072-13	Passenger seat belt pretensioner activation control	Passenger seat belt pretensioner circuit open	Using the electrical diagrams, check the passenger seat belt pretensioner circuit for an open
B0072-19	Passenger seat belt pretensioner activation control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0072-1A	Passenger seat belt pretensioner activation control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0072-95	Passenger seat belt pretensioner activation control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0080-11	Driver's seat belt load limiter activation control	Driver Seat Belt Retractor Circuit Short to Ground	Using the electrical diagrams, check the driver's seat belt retractor circuit for a short to ground
B008012	Driver's seat belt load limiter activation control	Electrical circuit of the driver's seat belt retractor: short circuit to the power supply circuit	Using the electrical diagrams, check the driver's seat belt retractor circuit for a short to power
B0080-13	Driver's seat belt load limiter activation control	Driver's seat belt retractor circuit open	Using the electrical diagrams, check the driver's seat belt retractor circuit for an open circuit
B0080-19	Driver's seat belt load limiter activation control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0080-1A	Driver's seat belt load limiter activation control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0080-95	Driver's seat belt load limiter activation control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B0082-11	Passenger seat belt load limiter activation control	Passenger Seat Belt Retractor Circuit Short to Ground	Using the electrical diagrams, check the passenger seat belt retractor circuit for a short to ground
B0082-12	Passenger seat belt load limiter activation control	Passenger seat belt retractor circuit: short circuit to power	Using the electrical diagrams, check the passenger seat belt retractor circuit for a short to power
B0082-13	Passenger seat belt load limiter activation control	Passenger seat belt retractor circuit open	Using the electrical diagrams, check the passenger seat belt retractor circuit for an open circuit
B0082-19	Passenger seat belt load limiter activation control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0082-1A	Passenger seat belt load limiter activation control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B0082-95	Passenger seat belt load limiter activation control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B00B5-11	Driver's seat runner position lock sensor	Driver Seat Position Sensor Circuit Short to Ground	Using the electrical circuit diagrams, check the driver seat track position sensor circuit for a short to ground
B00B5-12	Driver's seat runner position lock sensor	Driver Seat Position Sensor Circuit Short to Power	Using the electrical circuit diagrams, check the driver seat track position sensor circuit for a short to power
B00B5-13	Driver's seat runner position lock sensor	Driver Seat Position Sensor Circuit: Open Circuit	Using the electrical diagrams, check the driver's seat track position sensor circuit for an open
B00B5-19	Driver's seat runner position lock sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B00B5-1E	Driver's seat runner position lock sensor	Electrical circuit resistance is out of acceptable range	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B00B5-95	Driver's seat runner position lock sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B00D2-68	Supplemental Restraint System Malfunction Indicator 1 (Information DTC Only)	Event Information	Check the instrument cluster for DTCs and refer to the appropriate DTC index
B00D5-12	Passenger passive safety system deactivation indicator	Front passenger airbag deactivation indicator circuit: short circuit in power supply	Using the electrical diagrams, check the passenger airbag deactivation indicator lamp circuit for a short to power
B00D5-14	Passenger passive safety system deactivation indicator	Passenger Air Bag Off Indicator Circuit: Short to Ground, Open Circuit	Using the electrical circuit diagrams, check the passenger air bag deactivation indicator lamp circuit for a short to ground and an open circuit
B00D5-95	Passenger passive safety system deactivation indicator	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B00DF-24	Passenger passive safety system switch	Front passenger airbag deactivation switch: signal level is constantly high	Install a new passenger air bag switch. For additional information, refer to: Passenger Air Bag (PAD) Switch (501-20B Supplemental Restraint System, Removal and Installation).
B00DF-64	Passenger passive safety system switch	Front Passenger Airbag Deactivation Switch: Signal Level Constantly Low	Install a new passenger air bag switch. For additional information, refer to: Passenger Air Bag (PAD) Switch (501-20B Supplemental Restraint System, Removal and Installation).
B10FD-11	Driver side peripheral acceleration sensor	Driver Side B-Pillar Side Impact Sensor Circuit Short to Ground	Using the electrical diagrams, check the driver side B-pillar side impact sensor for a short to ground
B10FD-12	Driver side peripheral acceleration sensor	Driver Side B-Pillar Side Impact Sensor Circuit Short to Power	Using the electrical diagrams, check the driver side B-pillar side impact sensor for a short to power
B10FD-19	Driver side peripheral acceleration sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B10FD-4A	Driver side peripheral acceleration sensor	Incorrect element installed	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B10FD-87	Driver side peripheral acceleration sensor	Driver side B-pillar side impact force sensor circuit: open circuit. Internal sensor failure.	Refer to the electrical circuit diagrams and check the driver side 'B' pillar side impact sensor circuit for open circuit. Install a new sensor if necessary. For additional information, refer to: Pillar Side Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B10FD-95	Driver side peripheral acceleration sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B10FD-96	Driver side peripheral acceleration sensor	Internal component failure	Install a new side impact sensor to the B-pillar on the passenger side. For additional information, refer to the chapter: Side Impact Sensor - Pillar (501-20B Supplemental Restraint System, Removal and Installation).
B10FE-11	Passenger side peripheral acceleration sensor	Passenger Side B-Pillar Side Impact Sensor Circuit Short to Ground	Using the electrical diagrams, check the passenger side B-pillar side impact sensor for a short to ground
B10FE-12	Passenger side peripheral acceleration sensor	Passenger Side B-Pillar Side Impact Sensor Circuit Short to Power	Using the electrical diagrams, check the passenger side B-pillar side impact sensor for a short to power
B10FE-19	Passenger side peripheral acceleration sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B10FE-4A	Passenger side peripheral acceleration sensor	Incorrect element installed	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B10FE-87	Passenger side peripheral acceleration sensor	Passenger side B-pillar side impact sensor circuit: open circuit. Internal sensor failure.	Refer to the electrical circuit diagrams and check the passenger side B-pillar side impact sensor circuit for open. Install a new sensor if necessary. For additional information, refer to: B-Pillar Side Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B10FE-95	Passenger side peripheral acceleration sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B10FE-96	Passenger side peripheral acceleration sensor	Internal component failure	Install a new side impact sensor to the B-pillar on the passenger side. For additional information, refer to the chapter: Side Impact Sensor - Pillar (501-20B Supplemental Restraint System, Removal and Installation).
B1126-11	Driver side: side airbag deployment control	Short circuit of the driver's side airbag circuit to ground	Using the electrical diagrams, check the driver side airbag circuit for a short to ground
B1126-12	Driver side: side airbag deployment control	Driver side airbag circuit short to power	Using the electrical diagrams, check the driver side airbag circuit for a short to power
B1126-13	Driver side: side airbag deployment control	Driver side airbag circuit: open circuit	Using the electrical diagrams, check the driver's side airbag circuit for an open
B1126-19	Driver side: side airbag deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1126-1A	Driver side: side airbag deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1126-95	Driver side: side airbag deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1127-11	Passenger side: side airbag deployment control	Front passenger side airbag circuit short to ground	Using the electrical diagrams, check the passenger side airbag circuit for a short to ground
B1127-12	Passenger side: side airbag deployment control	Electric circuit of the front passenger side airbag: short circuit to the power supply circuit	Using the electrical diagrams, check the passenger side airbag circuit for a short to power
B1127-13	Passenger side: side airbag deployment control	Passenger side airbag circuit: open circuit	Using the electrical diagrams, check the passenger side airbag circuit for an open
B1127-19	Passenger side: side airbag deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1127-1A	Passenger side: side airbag deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1127-95	Passenger side: side airbag deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1128-11	Driver's side: side curtain airbag deployment control	Driver Side Front Curtain Airbag Circuit Short to Ground	Using the electrical circuit diagrams, check the driver front side airbag module circuit for a short to ground
B1128-12	Driver's side: side curtain airbag deployment control	Driver Side Front Curtain Airbag Circuit Short to Power	Using the electrical circuit diagrams, check the driver front side airbag module circuit for a short to power
B1128-13	Driver's side: side curtain airbag deployment control	Driver side front curtain airbag circuit: open circuit	Using the electrical circuit diagrams, check the driver front side airbag module circuit for an open
B1128-19	Driver's side: side curtain airbag deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1128-1A	Driver's side: side curtain airbag deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1128-95	Driver's side: side curtain airbag deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1129-11	Passenger side: side curtain airbag deployment control	Front passenger side curtain airbag circuit: short to ground	Using the electrical circuit diagrams, check the passenger front side airbag module circuit for a short to ground
B1129-12	Passenger side: side curtain airbag deployment control	Front passenger side curtain airbag circuit: short to power	Using the electrical circuit diagrams, check the passenger front side airbag module circuit for a short to power
B1129-13	Passenger side: side curtain airbag deployment control	Front passenger side curtain airbag circuit: open circuit	Using the electrical circuit diagrams, check the passenger front side airbag module circuit for an open
B1129-19	Passenger side: side curtain airbag deployment control	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1129-1A	Passenger side: side curtain airbag deployment control	Circuit resistance below threshold	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1129-95	Passenger side: side curtain airbag deployment control	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1193-68	The fault code recording block is full and locked (information DTC only)	Event Information	Check for related DTCs and refer to the appropriate DTC index
B1194-11	Front driver side acceleration sensor	Driver Side Front Impact Severity Sensor Circuit Short to Ground	Using the electrical diagrams, check the driver side front impact sensor circuit for a short to ground
B1194-12	Front driver side acceleration sensor	Driver Side Front Impact Sensor Circuit Short to Battery Voltage	Using the electrical diagrams, check the driver side front impact sensor circuit for a short to power
B1194-19	Front driver side acceleration sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1194-4A	Front driver side acceleration sensor	Incorrect element installed	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1194-87	Front driver side acceleration sensor	Driver side front impact force sensor circuit: open circuit. Internal sensor failure.	Refer to the electrical circuit diagrams and check the driver side front impact sensor circuit for an open. Install a new sensor if necessary. For additional information, refer to: Front Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1194-95	Front driver side acceleration sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1194-96	Front driver side acceleration sensor	Internal component failure	Install a new driver's side front impact sensor. For additional information, refer to: Front Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1195-11	Front passenger side acceleration sensor	Passenger Side Front Impact Sensor Circuit Short to Ground	Using the electrical diagrams, check the passenger side front impact sensor circuit for a short to ground
B1195-12	Front passenger side acceleration sensor	Front passenger side impact force sensor circuit: short circuit to power	Using the electrical diagrams, check the passenger side front impact sensor circuit for a short to power
B1195-19	Front passenger side acceleration sensor	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1195-4A	Front passenger side acceleration sensor	Incorrect element installed	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1195-87	Front passenger side acceleration sensor	Passenger side front impact sensor circuit: open circuit. Internal sensor failure.	Refer to the electrical circuit diagrams and check the passenger side front impact sensor circuit for an open. Install a new sensor if necessary. For additional information, refer to: Front Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1195-95	Front passenger side acceleration sensor	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1195-96	Front passenger side acceleration sensor	Internal component failure	Install a new passenger side front impact sensor. For additional information, refer to: Front Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1196-11	Peripheral acceleration sensor on the second row, driver's side	Driver Side C-Pillar Side Impact Sensor Circuit Short to Ground	Using the electrical circuit diagrams, check the driver side C-pillar side impact sensor circuit for a short to ground
B1196-12	Peripheral acceleration sensor on the second row, driver's side	Driver Side C-Pillar Side Impact Sensor Circuit Short to Power	Using the electrical circuit diagrams, check the driver side C-pillar side impact sensor circuit for a short to power
B1196-19	Peripheral acceleration sensor on the second row, driver's side	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1196-4A	Peripheral acceleration sensor on the second row, driver's side	Incorrect element installed	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1196-87	Peripheral acceleration sensor on the second row, driver's side	Driver side C-pillar side impact sensor circuit: open circuit. Internal sensor failure.	Refer to the electrical circuit diagrams and check the driver side C-pillar side impact sensor circuit for open circuit. Install a new sensor if necessary. For additional information, refer to: Pillar Side Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1196-95	Peripheral acceleration sensor on the second row with	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1196-96	Peripheral acceleration sensor on the second row, driver's side	Internal component failure	Install a new side impact sensor to the driver's side C-pillar. For additional information, refer to: Pillar Side Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1197-11	Peripheral acceleration sensor on the second row, passenger side	Passenger Side C-Pillar Side Impact Sensor Circuit Short to Ground	Using the electrical circuit diagrams, check the passenger side C-pillar side impact sensor circuit for a short to ground
B1197-12	Peripheral acceleration sensor on the second row, passenger side	Passenger Side C-Pillar Side Impact Sensor Circuit Short to Power	Using the electrical diagrams, check the passenger side C-pillar side impact sensor circuit for a short to power
B1197-19	Peripheral acceleration sensor on the second row, passenger side	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1197-4A	Peripheral acceleration sensor on the second row, passenger side	Incorrect element installed	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1197-87	Peripheral acceleration sensor on the second row, passenger side	Passenger side C-pillar side impact sensor circuit: open circuit. Internal sensor failure.	Refer to the electrical circuit diagrams and check the passenger side C-pillar side impact sensor circuit for open. Install a new sensor if necessary. For additional information, refer to: Pillar Side Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1197-95	Peripheral acceleration sensor on the second row, passenger side	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1197-96	Peripheral acceleration sensor on the second row, passenger side	Internal component failure	Install a new side impact sensor to the passenger side C-pillar. For additional information, refer to: Pillar Side Impact Sensor (501-20B Supplemental Restraint System, Removal and Installation).
B1A55-11	Collision detection unit output	Event signal circuit: short to ground	Using the electrical schematics, check the event signal circuit for a short to ground
B1A55-12	Collision detection unit output	Event signal circuit: short circuit to power supply	Using the electrical schematics, check the event signal circuit for a short to power
B1D74-11	Passenger airbag deactivation button	Passenger Air Bag Deactivation Switch Circuit: Short to Ground	Using the electrical diagrams, check the passenger air bag switch circuit for a short to ground
B1D74-12	Passenger airbag deactivation button	Passenger Air Bag Deactivation Switch Circuit: Short to Power	Using the electrical diagrams, check the passenger airbag switch circuit for a short to power
B1D74-13	Passenger airbag deactivation button	Passenger Air Bag Deactivation Switch Circuit: Open Circuit	Using the electrical diagrams, check the passenger airbag switch circuit for an open
B1D74-19	Passenger airbag deactivation button	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1D74-1E	Passenger airbag deactivation button	Electrical circuit resistance is out of acceptable range	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1D74-95	Passenger airbag deactivation button	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
B1D75-11	Passenger airbag deactivation lock button	Passenger Air Bag Deactivation Switch Circuit: Short to Ground	Using the electrical diagrams, check the passenger air bag switch circuit for a short to ground
B1D75-12	Passenger airbag deactivation lock button	Passenger Air Bag Deactivation Switch Circuit: Short to Power	Using the electrical diagrams, check the passenger airbag switch circuit for a short to power
B1D75-13	Passenger airbag deactivation lock button	Passenger Air Bag Deactivation Switch Circuit: Open Circuit	Using the electrical diagrams, check the passenger airbag switch circuit for an open
B1D75-19	Passenger airbag deactivation lock button	The current in the circuit is above the limit value	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1D75-1E	Passenger airbag deactivation lock button	Electrical circuit resistance is out of acceptable range	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
B1D75-95	Passenger airbag deactivation lock button	Incorrect assembly	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system. Check the CJB for DTCs and refer to the appropriate DTC index. For additional information, refer to the chapter: Communication Network (418-00 Module Communication Network, Diagnostics and Tests).
U0001-88	High-speed CAN communication bus	Bus shutdown	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U0140-00	Lost communication with the body control unit	No subtype information available	Perform CAN network integrity tests using the manufacturer approved diagnostic system.
U0154-00	No communication with the occupant classification module of the passive restraint system	No subtype information available	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U0155-00	Lost Communication with Instrument Panel Control (IPC)	No subtype information available	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U0300-00	Internal control unit software incompatibility	No subtype information available	Check for related DTCs for the CJB and refer to the appropriate DTC index. For additional information, refer to: Communication Network (418-00 Module Communication Network, Diagnostics and Testing). Check the RCM for related DTCs and refer to the DTC index. Ensure that the correct components are installed
U0455-64	Incorrect data received from the occupant classification module of the passive restraint system	Invalid signal readings	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U0455-92	Incorrect data received from the occupant classification module of the passive restraint system	Doesn't work or works incorrectly	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U0455-94	Incorrect data received from the occupant classification module of the passive restraint system	The work does not meet expectations	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U2100-00	Primary configuration is not configured	No subtype information available	Configure the RCM as a new module using the manufacturer approved diagnostic system
U2101-00	Control unit configuration incompatibility	No subtype information available	Check/correct the vehicle configuration file using the manufacturer approved diagnostic system.
U3000-49	Control unit	Internal failure of electronic equipment	Install a new RCM, refer to the New Module/Component Installation Note at the beginning of the DTC Index. For additional information, refer to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation).
U3003-62	Battery voltage	Battery voltage mismatch of 2V or more between RCM (Restraint Control Module) and CJB (Central Junction Box)	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U3006-17	Power input "A" of the control unit	Circuit voltage is above limit	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.
U3006-68	Power input "A" of the control unit	Event Information	Using the electrical diagrams, check the ignition/power lines of the RCM
U3008-13	Ground circuit "A" of the control unit	The electrical circuit is open	Perform the troubleshooting tests associated with this DTC using the manufacturer approved diagnostic system.