Front suspension of the car Land Rover Discovery 1
Front suspension — device
1 - Panhard rod, 2 - reaction rod, 3 - spring, 4 - shock absorber. The front axle is held horizontally by two torque rods and vertically by a Panhard rod. Each wheel is equipped with long-travel...
1 - Panhard rod, 2 - reaction rod, 3 - spring, 4 - shock absorber. The front axle is held horizontally by two torque rods and vertically by a Panhard rod. Each wheel is equipped with long-travel...
Panhard rod
1. Disconnect the rod from the frame. 2. Disconnect the traction from the bridge. 3. Remove the rod. 4. Press out the rubber bushings of the tie rod joints. 5. Press in new bushings. Caution: Apply...
1. Disconnect the rod from the frame. 2. Disconnect the traction from the bridge. 3. Remove the rod. 4. Press out the rubber bushings of the tie rod joints. 5. Press in new bushings. Caution: Apply...
Jet thrust
1. Loosen the wheel nuts. 2. Raise the front of the car, place it on stands under the frame, and remove the wheels. 3. Place a jack under the front axle and lift the axle. 4. Unscrew the nuts...
1. Loosen the wheel nuts. 2. Raise the front of the car, place it on stands under the frame, and remove the wheels. 3. Place a jack under the front axle and lift the axle. 4. Unscrew the nuts...
Front shock absorbers
1. Loosen the wheel nuts. 2. Raise the front of the car, place it on stands under the frame, and remove the wheels. 3. Place a jack under the front axle and lift the axle. 4. Unscrew the nuts of the...
1. Loosen the wheel nuts. 2. Raise the front of the car, place it on stands under the frame, and remove the wheels. 3. Place a jack under the front axle and lift the axle. 4. Unscrew the nuts of the...
Front suspension springs
1. Remove the shock absorber. Caution: Do not damage the brake hose. If necessary, loosen the hose connection to the bridge. 2. Lower the front axle until the springs are released. 3. Remove the...
1. Remove the shock absorber. Caution: Do not damage the brake hose. If necessary, loosen the hose connection to the bridge. 2. Lower the front axle until the springs are released. 3. Remove the...
Suspension travel limiter
1. Unscrew the limiter fasteners. 2. Remove the limiter. 3. Installation is carried out in reverse order.
1. Unscrew the limiter fasteners. 2. Remove the limiter. 3. Installation is carried out in reverse order.
Anti-roll bar
Removal 1. Mark the relative positions of the stabilizer and rubber bushings. 2. Unscrew the fastenings of the rubber bushing brackets. 3. Unscrew the ball joint fasteners to the stabilizer, remove...
Removal 1. Mark the relative positions of the stabilizer and rubber bushings. 2. Unscrew the fastenings of the rubber bushing brackets. 3. Unscrew the ball joint fasteners to the stabilizer, remove...
Stabilizer link joints
1. Unscrew the ball joint fasteners of the stabilizer rods. 2. Remove the cotter pin and loosen the castle nut a few turns. 1 - stabilizer, 2 - rubber bushing, 3 - bushing bracket, 4 - bolt, nut and...
1. Unscrew the ball joint fasteners of the stabilizer rods. 2. Remove the cotter pin and loosen the castle nut a few turns. 1 - stabilizer, 2 - rubber bushing, 3 - bushing bracket, 4 - bolt, nut and...
Tightening torques for threaded connections (Nm)
Front stabilizer: bracket nut - 30 tie rod nut - 68 crown nut - 40 Longitudinal thrust to the axle - 40 Tunnel strut nut - 40 Lateral thrust to chassis - 176 Panhard rod to chassis - 88 Panhard row -...
Front stabilizer: bracket nut - 30 tie rod nut - 68 crown nut - 40 Longitudinal thrust to the axle - 40 Tunnel strut nut - 40 Lateral thrust to chassis - 176 Panhard rod to chassis - 88 Panhard row -...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian