Car cruise control Land Rover Discovery 1
Speed control system («Cruise Control») — description
Note: Models with manual transmission are equipped with a clutch pedal switch. The cruise control system can be activated at speeds above 45 km / h and automatically turns off at speeds below 42 km /...
Note: Models with manual transmission are equipped with a clutch pedal switch. The cruise control system can be activated at speeds above 45 km / h and automatically turns off at speeds below 42 km /...
Checking the operation of the cruise control system
Caution: Do not use the cruise control system when reversing or when the transfer case is in low gear. It is not recommended to turn on the system in strong winds, snowfall, or heavy traffic....
Caution: Do not use the cruise control system when reversing or when the transfer case is in low gear. It is not recommended to turn on the system in strong winds, snowfall, or heavy traffic....
Brake/Clutch Pedal Switches
1. Unscrew the fasteners of the front panel cover on the driver's side. 2. Remove the panel and move it to the side. 3. Release the locking sleeve. 4. Remove the switch from the pedal bracket. 5....
1. Unscrew the fasteners of the front panel cover on the driver's side. 2. Remove the panel and move it to the side. 3. Release the locking sleeve. 4. Remove the switch from the pedal bracket. 5....
Main switch
1. Disconnect the battery. 2. Carefully remove the switch block from the front panel. 3. Disconnect the switch connector. 4. Press the switch mounting latches and remove it from the panel. Replacing...
1. Disconnect the battery. 2. Carefully remove the switch block from the front panel. 3. Disconnect the switch connector. 4. Press the switch mounting latches and remove it from the panel. Replacing...
Control switch
1. Disconnect the battery. 2. On models with an airbag: Remove the driver's side airbag unit (see " Passive safety system "). 3. On models without an airbag: Turn the steering wheel 90 degrees....
1. Disconnect the battery. 2. On models with an airbag: Remove the driver's side airbag unit (see " Passive safety system "). 3. On models without an airbag: Turn the steering wheel 90 degrees....
Current collector — removal and installation
The current collector is installed behind the steering wheel. To access the current collector, you need to remove the steering wheel and steering column pads. Note: On models with an airbag, remove...
The current collector is installed behind the steering wheel. To access the current collector, you need to remove the steering wheel and steering column pads. Note: On models with an airbag, remove...
Cruise control system drive (V8i)
Note: the drive is not repairable. If the drive is damaged, install a new unit. 1. Disconnect the battery. 2. Disconnect the vacuum hose from the drive. 3. Unscrew the nut securing the drive to the...
Note: the drive is not repairable. If the drive is damaged, install a new unit. 1. Disconnect the battery. 2. Disconnect the vacuum hose from the drive. 3. Unscrew the nut securing the drive to the...
Drive traction control (V8i)
1. Turn off the ignition. 2. Measure the gap between the drive rod and the groove of the throttle lever finger: the gap should be 0.2 - 2.0 mm (with the throttle closed). 3. If not, remove the drive...
1. Turn off the ignition. 2. Measure the gap between the drive rod and the groove of the throttle lever finger: the gap should be 0.2 - 2.0 mm (with the throttle closed). 3. If not, remove the drive...
Vacuum pump (Tdi)
Note: the pump is not repairable. If the pump is damaged, install a new unit. 1. Release the pump cover latches and remove the cover. 2. Unfasten the jack mounting clamp and remove the jack. 3....
Note: the pump is not repairable. If the pump is damaged, install a new unit. 1. Release the pump cover latches and remove the cover. 2. Unfasten the jack mounting clamp and remove the jack. 3....
Cruise control unit (V8i)
1. Remove the bottom cover of the front panel. 2. Disconnect the control unit connector. 3. Unscrew the control unit fasteners. 4. Remove the control unit. 5. Installation is carried out in reverse...
1. Remove the bottom cover of the front panel. 2. Disconnect the control unit connector. 3. Unscrew the control unit fasteners. 4. Remove the control unit. 5. Installation is carried out in reverse...
Neutral position relay
1. Release the fasteners of the right trim panel. 2. Move the panel aside. 3. Unscrew the 2 studs securing the lower trim of the right A-pillar. 4. Remove the cover. 5. Remove the relay (not...
1. Release the fasteners of the right trim panel. 2. Move the panel aside. 3. Unscrew the 2 studs securing the lower trim of the right A-pillar. 4. Remove the cover. 5. Remove the relay (not...
Cruise control system drive (Tdi)
Note: the drive is not repairable. If the drive is damaged, install a new unit. 1. Disconnect the battery. 2. Remove the cotter pin and the pin securing the cable to the lever. 3. Disconnect the ball...
Note: the drive is not repairable. If the drive is damaged, install a new unit. 1. Disconnect the battery. 2. Remove the cotter pin and the pin securing the cable to the lever. 3. Disconnect the ball...
Cruise control unit (Tdi)
1. Disconnect the 4 studs securing the lower left front panel cover. 2. Remove the cover. 3. Unscrew the control unit mounting clamp nut. 4. Lower the clamp to provide access to the mounting nut. 5....
1. Disconnect the 4 studs securing the lower left front panel cover. 2. Remove the cover. 3. Unscrew the control unit mounting clamp nut. 4. Lower the clamp to provide access to the mounting nut. 5....
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian