Car steering Land Rover Discovery 1

Steering — Description
1 - pump, 2 - pump reservoir, 3 - steering gear, 4 - steering column, 5 - cardan joints, 6 - shaft, 7 - compensation unit, 8 - transverse rod. Description Power steering with a compensating unit on...

Checking the power steering system
1. The pressure in the power steering system can reach 105 bar. The pressure changes proportionally to the steering wheel rotation. 2. Check the fluid level in the power steering pump reservoir. 3....

Roadside inspection
Note: This test is only valid for tires recommended for installation on the vehicle. Before checking 1. Check tire pressure. 2. Check the condition of the tire tread. 3. Make sure that the same type...

Steering wheel adjustments
Power steering Please note: power steering adjustments are prohibited during the warranty period 1. Apply the parking brake or move the automatic transmission selector to position "P". Place the...

Determining the central position of the steering gear
Install an 8mm diameter pin into the holes in the pitman arm and steering gear housing. The alignment of these holes determines the central position of the steering gear.

Wheel rotation limiter
1. Measure the clearance between the tire sidewall and the steering arm at maximum wheel angle. This gap should be 20 mm. Adjustment 2. Loosen the lock nut of the limiter bolt. 3. Turn the bolt to...

Wheel alignment angles
Note: Wheel camber and kingpin caster are not adjustable. Checking the alignment 1. Place the vehicle on a level, horizontal surface. Steered wheels in straight-ahead position. 2. Roll the vehicle...

Tubes and hoses
Caution: Before disconnecting the tube or hose, clean the connection area. After disconnecting, plug the hose or tube and fitting. Replacing the power steering pump hoses 1. Remove the plug from the...

Steering gear
General instructions 1. Assembly and disassembly of the mechanism must be carried out in absolute cleanliness. 2. If metal dust is detected in the power steering fluid, determine the cause of the...

Bleeding the power steering system
1. Add fluid to the pump reservoir up to the upper mark on the dipstick. 2. Warm up the engine to operating temperature. 3. Recheck the fluid level in the reservoir. Note: when performing steps 4–6,...

Power steering pump reservoir
Removal 1. Remove the engine protection. 2. Place a container under the pump tank to collect the liquid. 3. Loosen the tank clamp bolt and lift the tank until the hose clamps are released. 4. Loosen...

Power steering pump (V8i engine)
Removal Attention: the pump cannot be repaired and must be replaced with a new one. 1. Disconnect the battery. 2. Remove the accessory drive belt. 3. Remove the engine protection. 4. Remove the fan...

Power steering pump (TDi engine)
Removal 1. Remove the fan together with the viscous coupling. 2. Loosen the three pump pulley mounting bolts. 3. Remove the accessory drive belt. 4. Remove the three pulley mounting bolts and the...

Steering cardan shaft
Attention: 1. Before disconnecting any steering component, set the steering wheels to the straight-ahead position. To avoid damaging the steering column current collector, remove the steering wheel....

Steering column pads
1. Disconnect the battery. 2. Remove the three screws securing the trim. 3. Carefully separate the halves of the overlay. 4. Remove the pads. 5. Installation is carried out in reverse order.

Steering wheel
Attention: For owners of vehicles with airbags, we recommend reading the section "Passive Safety System". Please also read the warnings section " Steering cardan shaft ". Removal 1. Disconnect the...

Upper part of the steering column
Note: The upper part of the steering column is not serviceable. Please read the warnings section " Steering cardan shaft ". Removal 1. Remove the steering wheel. Secure the current collector with...

Steering column lock
Please read the warnings section " Steering cardan shaft ". Removal 1. Disconnect the battery. 2. Remove the steering column covers. 3. Remove the lower access panel on the driver's side. 4. If...

Bipod — removal and installation
Removal 1. Raise the car on a lift. 2. Disconnect the ball joint of the longitudinal steering rod from the steering knuckle. To remove the joint you will need the LRT-57-018 puller. 3. Bend back the...

Steering shock absorber
1. Raise the car on a lift. 2. Disconnect the shock absorber fasteners from the final drive housing bracket. 3. Disconnect the shock absorber fasteners from the tie rod bracket. 4. Remove the shock...

Transverse steering rod
Removal 1. Raise the car on a lift. 2. Disconnect the steering shock absorber from the rod. 3. Using the LRT-57-018 puller, remove the ball joints of the tie rod ends. 4. Remove the rod. Disassembly...

Longitudinal steering rod
Removal 1. Check the wheel alignment. 2. Set the steering wheels to the straight-ahead position. 3. Raise the car on a lift. 4. Remove the right front wheel. 5. Using the LRT-57-018 puller,...

Steering gear
Repair Please note: repair of the mechanism is not permitted during the warranty period. Assembly and disassembly of the mechanism must be carried out in absolute cleanliness. 1. Remove the steering...

Power steering pump
Type/manufacturer: V8i - ZF "Unicorn" TDI - Hobourn Eaton 500 Working pressure: idle, straight-line movement - less than 7 bar; idle, full rotation - more than 28 bar; 1000 rpm, full rotation - 70-77...

Special tool
Bipod puller — LRT-57-012 Key - LRT-57-007 Worm Gear Adjuster Key — LRT-57-006 Ring Expander — LRT-57-019 Ring crimping machine — LRT-57-020 Sector shaft seal fuse — LRT-57-021 Worm shaft seal...

Brake pads (front wheels)
Note: After installing new brake pads, they will be run in for several hundred kilometers until they achieve maximum braking efficiency. Note: when replacing the pads, you will need the LRT-70-500...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Discovery 3

Discovery 1