Petrol engine V8i (4.0L) of car Land Rover Discovery 1
Only those operations that are not included in the V8 engine or are different from similar operations for the specified engine are listed here.
Crankshaft pulley
Removal 1. Disconnect the battery. 2. Remove the cooling fan. 3. Loosen the three water pump pulley mounting bolts. 4. Remove the belt (see 3.9 V8 engine). 5. Remove the bolts and water pump pulley....
Removal 1. Disconnect the battery. 2. Remove the cooling fan. 3. Loosen the three water pump pulley mounting bolts. 4. Remove the belt (see 3.9 V8 engine). 5. Remove the bolts and water pump pulley....
Front crankshaft oil seal
Removal 1. Remove the crankshaft pulley. 2. Screw the LRT puller - 12-088 into the oil seal. 3. By tightening the central bolt of the puller, press out the oil seal. Installation 4. Clean the oil...
Removal 1. Remove the crankshaft pulley. 2. Screw the LRT puller - 12-088 into the oil seal. 3. By tightening the central bolt of the puller, press out the oil seal. Installation 4. Clean the oil...
Engine — removal and installation
Removal 1. Place the car on a lift. 2. Remove the hood (see " Body "). 3. Remove the radiator (see section " Cooling system "). 4. Remove the resonance chamber (see " Fuel system "). 5. Remove the...
Removal 1. Place the car on a lift. 2. Remove the hood (see " Body "). 3. Remove the radiator (see section " Cooling system "). 4. Remove the resonance chamber (see " Fuel system "). 5. Remove the...
Front cover gasket
Removal 1. Disconnect the battery. 2. Drain the coolant. 3. Remove the radiator. 4. Remove the water pump pulley. 5. Disconnect the lower water pump hose. 6. Raise the car on a lift. 7. Disconnect...
Removal 1. Disconnect the battery. 2. Drain the coolant. 3. Remove the radiator. 4. Remove the water pump pulley. 5. Disconnect the lower water pump hose. 6. Raise the car on a lift. 7. Disconnect...
Left valve cover gasket
Removal 1. Disconnect the battery. 2. Remove the resonance chamber. 3. Loosen the screw securing the oil dipstick tube to the valve cover. 4. Release the high-voltage wires from the clip on the...
Removal 1. Disconnect the battery. 2. Remove the resonance chamber. 3. Loosen the screw securing the oil dipstick tube to the valve cover. 4. Release the high-voltage wires from the clip on the...
Right valve cover gasket
Removal 1. Relieve residual pressure in the fuel system. 2. Disconnect the battery. 3. Drain the coolant. Note: There is no need to disconnect the hoses now. 4. Disconnect the fuel vapor accumulator...
Removal 1. Relieve residual pressure in the fuel system. 2. Disconnect the battery. 3. Drain the coolant. Note: There is no need to disconnect the hoses now. 4. Disconnect the fuel vapor accumulator...
Rear crankshaft oil seal
1. Manual transmission: remove the flywheel. 2. Automatic transmission: remove the torque converter drive clutch. 3. Remove the rear oil seal. Caution: Do not damage the oil seal seat. Installation...
1. Manual transmission: remove the flywheel. 2. Automatic transmission: remove the torque converter drive clutch. 3. Remove the rear oil seal. Caution: Do not damage the oil seal seat. Installation...
Torque converter clutch (automatic transmission)
1. Remove the gearbox and torque converter (see " Automatic transmission LT230T "). 2. Unscrew the 4 bolts of the ring spacer. 3. Remove the half coupling with the toothed ring. 4. Unscrew the 6...
1. Remove the gearbox and torque converter (see " Automatic transmission LT230T "). 2. Unscrew the 4 bolts of the ring spacer. 3. Remove the half coupling with the toothed ring. 4. Unscrew the 6...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian