Rear suspension of car Land Rover Discovery 1
Rear suspension — device
1 - A-shaped lever, 2 - reaction rod, 3 - spring, 4 - shock absorber. The rear axle is held in the horizontal plane by two reaction rods, and in the vertical plane by an A-shaped lever. Shock...
1 - A-shaped lever, 2 - reaction rod, 3 - spring, 4 - shock absorber. The rear axle is held in the horizontal plane by two reaction rods, and in the vertical plane by an A-shaped lever. Shock...
Rear suspension springs
1. Loosen the wheel nuts. 2. Raise the rear of the car, place it on stands under the frame, and remove the wheels. 3. Place a jack under the rear axle and lift the axle. 4. Disconnect the upper shock...
1. Loosen the wheel nuts. 2. Raise the rear of the car, place it on stands under the frame, and remove the wheels. 3. Place a jack under the rear axle and lift the axle. 4. Disconnect the upper shock...
Rear shock absorber
1. Loosen the wheel nuts. 2. Raise the rear of the car, place it on stands under the frame, and remove the wheels. Place a jack under the rear axle and lift the axle. 3. Disconnect the shock absorber...
1. Loosen the wheel nuts. 2. Raise the rear of the car, place it on stands under the frame, and remove the wheels. Place a jack under the rear axle and lift the axle. 3. Disconnect the shock absorber...
Suspension travel limiter
1. Unscrew the limiter fasteners. 2. Remove the limiter. 3. Installation is carried out in reverse order.
1. Unscrew the limiter fasteners. 2. Remove the limiter. 3. Installation is carried out in reverse order.
A-arm bushings
1. Raise the vehicle and lift the rear axle off the ground. Place supports under the frame. 2. Unscrew the lever bracket fasteners to the frame. 3. Remove the control arm axle bolt on the rear axle....
1. Raise the vehicle and lift the rear axle off the ground. Place supports under the frame. 2. Unscrew the lever bracket fasteners to the frame. 3. Remove the control arm axle bolt on the rear axle....
Jet thrust bushings
1. Raise the car on a lift. 2. If there is no lift, place the vehicle on stands placed under the rear axle. 3. Unscrew the rear tie rod fasteners. 4. Unscrew the front tie rod fasteners. 5. Remove...
1. Raise the car on a lift. 2. If there is no lift, place the vehicle on stands placed under the rear axle. 3. Unscrew the rear tie rod fasteners. 4. Unscrew the front tie rod fasteners. 5. Remove...
Anti-roll bar
Removal 1. Mark the relative positions of the stabilizer and rubber bushings. 2. Unscrew the rubber bushing bracket fasteners. 3. Unscrew the ball joint fasteners to the stabilizer, remove the...
Removal 1. Mark the relative positions of the stabilizer and rubber bushings. 2. Unscrew the rubber bushing bracket fasteners. 3. Unscrew the ball joint fasteners to the stabilizer, remove the...
Stabilizer link joints
1. Unscrew the ball joint fasteners of the stabilizer rods. 2. Remove the cotter pin and loosen the castle nut a few turns. 3. Using puller 18G1063A, remove the ball joint from the rod. 1 -...
1. Unscrew the ball joint fasteners of the stabilizer rods. 2. Remove the cotter pin and loosen the castle nut a few turns. 3. Using puller 18G1063A, remove the ball joint from the rod. 1 -...
Tightening torques for threaded connections (Nm)
Rear stabilizer: bracket nut - 30 tie rod nut - 68 crown nut - 40 Upper link to bracket - 176 Lower link to axle - 176 Lower link to frame - 176 Upper link bracket to crossmember - 47 Shock absorber...
Rear stabilizer: bracket nut - 30 tie rod nut - 68 crown nut - 40 Upper link to bracket - 176 Lower link to axle - 176 Lower link to frame - 176 Upper link bracket to crossmember - 47 Shock absorber...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian