Gasoline engine Mpi of car Land Rover Discovery 1
MPi Engine Description
The MPi engine is a four-cylinder, water-cooled engine with an aluminum alloy head and block and two overhead camshafts. Belongs to the "T" series of engines. The crankshaft has full support, the...
The MPi engine is a four-cylinder, water-cooled engine with an aluminum alloy head and block and two overhead camshafts. Belongs to the "T" series of engines. The crankshaft has full support, the...
Replacing the camshaft oil seal
Removal 1. Disconnect the battery. 2. Remove the accessory drive belt. 3. Remove the 5 upper timing belt cover bolts. 4. Remove the upper timing belt cover. 5. Remove the 5 timing belt center cover...
Removal 1. Disconnect the battery. 2. Remove the accessory drive belt. 3. Remove the 5 upper timing belt cover bolts. 4. Remove the upper timing belt cover. 5. Remove the 5 timing belt center cover...
Camshaft plugs
Removal 1. Remove the cylinder head. 2. Use a lever to remove the plug. Installation 1. Clean the plug seat. 2. Install the plug into the head by striking the outer edge. 3. Install the cylinder head.
Removal 1. Remove the cylinder head. 2. Use a lever to remove the plug. Installation 1. Clean the plug seat. 2. Install the plug into the head by striking the outer edge. 3. Install the cylinder head.
Front crankshaft oil seal
Removal 1. Remove the timing belt. 2. Remove the crankshaft gear and key. Place the puller stop on the crankshaft. 3. Screw the LRT-12-073 puller onto the front oil seal. 4. By tightening the central...
Removal 1. Remove the timing belt. 2. Remove the crankshaft gear and key. Place the puller stop on the crankshaft. 3. Screw the LRT-12-073 puller onto the front oil seal. 4. By tightening the central...
Rear crankshaft oil seal
1. Remove the gearbox. 2. Remove the clutch. 3. Remove the flywheel. 4. Drain the engine oil. 5. Replace the drain plug. Replace the sealing washer if necessary. 6. Loosen the 15 oil pan mounting...
1. Remove the gearbox. 2. Remove the clutch. 3. Remove the flywheel. 4. Drain the engine oil. 5. Replace the drain plug. Replace the sealing washer if necessary. 6. Loosen the 15 oil pan mounting...
Engine — removal and installation
Removal 1. Place the car on a lift. 2. Remove the accessory drive belt. 3. Remove the radiator (see " Cooling system "). 4. Remove the hood (see " Body "). 5. Drain the engine oil. 6. Place a rag...
Removal 1. Place the car on a lift. 2. Remove the accessory drive belt. 3. Remove the radiator (see " Cooling system "). 4. Remove the hood (see " Body "). 5. Drain the engine oil. 6. Place a rag...
Pallet gasket
Removal 1. Drain the engine oil. 2. Tighten the drain plug. Replace the sealing washer if necessary. 3. Unscrew the 18 pan mounting bolts. Note: There are 25mm long bolts installed in the right rear...
Removal 1. Drain the engine oil. 2. Tighten the drain plug. Replace the sealing washer if necessary. 3. Unscrew the 18 pan mounting bolts. Note: There are 25mm long bolts installed in the right rear...
Cylinder head gasket
1. Disconnect the battery. 2. Relieve residual fuel pressure in the system, disconnect the fuel supply line. Attention: perform the next step only on a cold engine. 3. Disconnect the lower radiator...
1. Disconnect the battery. 2. Relieve residual fuel pressure in the system, disconnect the fuel supply line. Attention: perform the next step only on a cold engine. 3. Disconnect the lower radiator...
Valve cover gasket
Removal 1. Unscrew the 4 spark plug cover mounting screws. 2. Remove the spark plug cover. Intake only 3. Disconnect the two crankcase ventilation hoses from the valve cover. 4. Remove the 4 screws...
Removal 1. Unscrew the 4 spark plug cover mounting screws. 2. Remove the spark plug cover. Intake only 3. Disconnect the two crankcase ventilation hoses from the valve cover. 4. Remove the 4 screws...
Timing belt
Removal Note: If the belt is to be removed from the camshaft sprockets only, there is no need to remove the accessory belt, crankshaft pulley, or lower belt cover. 1. Remove the accessory drive belt....
Removal Note: If the belt is to be removed from the camshaft sprockets only, there is no need to remove the accessory belt, crankshaft pulley, or lower belt cover. 1. Remove the accessory drive belt....
Tightening torques for threaded connections (Nm)
Front timing belt cover bolts - 5 Crankshaft pulley center bolt - 85 Crankshaft pulley bolts - 20 Timing belt tensioner bolt - 30 Spark plugs - 25 Rear timing belt cover bolts - 10 Camshaft Timing...
Front timing belt cover bolts - 5 Crankshaft pulley center bolt - 85 Crankshaft pulley bolts - 20 Timing belt tensioner bolt - 30 Spark plugs - 25 Rear timing belt cover bolts - 10 Camshaft Timing...
Special tool
Engine Lift Bracket — LRT-12-056 18G1644 Mounting pins (valve timing) — LRT-12-058 18G1523 Crankshaft Pulley Locking Tool — LRT-12-059 18G1641 Crankshaft Gear Locking Tool — LRT-12-060 18G1524 Safety...
Engine Lift Bracket — LRT-12-056 18G1644 Mounting pins (valve timing) — LRT-12-058 18G1523 Crankshaft Pulley Locking Tool — LRT-12-059 18G1641 Crankshaft Gear Locking Tool — LRT-12-060 18G1524 Safety...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian