2.7l engine specification (Discovery 3)

Seals

Name	Land Rover Part Number
Distribution box covers	8510302
T-joints - between ladder structure and engine block	STC 50550
Coolant Drain Plug - Threaded	STC 50552
Upper middle oil pump mounting bolt	STC 50552

Lubricants

Name	Specification
Motor oil, SAE 5W-30	Use 5W/30 engine oil according to specification WSS-M2C-913B, meeting ACEA B1/B3 requirements

Note: WSS is a code used by Ford in oil specifications Filling Capacities

Filling volumes, engine oil	Specification
Dry fill including filter for factory installed engine	6.55 l (11.5 pints) (6.9 US quarts)
Dry fill, including filter, for all new engines installed during maintenance	7.05 l (12.4 pints) (7.4 US quarts)
Oil and filter change	5.54 L (9.6 pints) (5.8 US quarts)
The amount of oil required to raise the oil level on the dipstick from the 'MIN' mark to the 'MAX' mark	1.5L (2.6 pints) (1.6 US quarts)

Dimensions

Position	Specification
Length	523 mm (20 59 in)
Width	717 mm (2825 in)
Height	771 mm (3035 in)

General specifications

Name	Specification
Type	Engine with a displacement of 2.7 liters, V-shaped cylinder arrangement with a camber angle of 60 degrees, battery fuel system, turbocharger and intercooler, two overhead camshafts and four valves per cylinder
Cylinder arrangement	V6, cylinders 1 and 4 are located at the front when looking at the engine from behind
Cylinder numbering	Cylinder 1 - right row; cylinder 4 - left row
Cylinder diameter - nominal	810 mm (3188 in)
Piston stroke	88 0 mm (3464 in)
Working volume	2720 cm³ (165.9 in³)
Cylinder firing order	1 - 4 - 2 - 5 - 3 - 6
Compression ratio	17,3:1
Direction of rotation	Counterclockwise when looking at the engine from behind
Maximum power	147 kW (200 hp) (effective power 197 hp.) at 4000 rpm
Maximum torque	440 Nm (324 ft·lbs) at 1900 rpm
Engine oil pressure:
In idle mode	0.7 bar (70 kPa) (10 psi)
at 3500 rpm	1.9 bar (190 kPa) (27.5 psi)

Tightening torque specifications

Name	Nm	lb-ft
Bolt for fastening the auxiliary drive belt roller	47	35
Bolts M8 for fastening the auxiliary drive belt tensioner	47	35
Bolts M10 for fastening the auxiliary drive belt tensioner	25	18
Air Conditioning Compressor Mounting Bolts	23	17
Air Conditioning Compressor Mounting Bolts	23	17
Air Conditioner Low Pressure Line Fasteners	9	7
Air conditioning pipe mounting bolt	20	15
Positive Battery Cable Mounting Bolts	10	7
* Inner camshaft bearing cover mounting bolts
Step 1: Tighten bolts 1 through 14	1	1
Step 2: Tighten bolts 1 through 14	5	4
Step 3: Tighten bolts 1 through 14	10	7
* Camshaft outer bearing cover mounting bolts
Step 1: Tighten bolts 1 through 4	1	1
Step 2: Tighten bolts 1 through 4	5	4
Step 3: Tighten bolts 1 through 4	10	7
Camshaft Position Sensor Mounting Bolt	10	7
+1 Camshaft coupling mounting bolts
Step 1	80	59
Step 2	Another 90°	Another 90°
Camshaft Pulley Mounting Bolts	23	17
Timing Belt Cover Fastening Bolts	10	7
+1 Bolt for fastening the crankshaft pulley
Step 1	100	74
Step 2	Another 90°	Another 90°
Crankshaft Pulley Damper Bolts	14	10
Crankshaft position sensor mounting bolt	5	4
Crankshaft rear oil seal support plate	10	7
Cooling system outlet elbow pipe	10	7
*+2 Cylinder head mounting bolts
Step 1	20	15
Step 2	40	30
Step 3	80	59
Step 4	Another 180°	Another 180°
Heat shield for front differential support	10	7
EGR valve inlet pipe	10	7
EGR valve mounting bolts	10	7
EGR valve bracket fastener	10	7
Positive crankcase ventilation tube mounting bolt	10	7
Engine mount to cross beam mounting nuts	62	46
Engine mount bracket to engine mount mounting bolts	62	46
Engine support bracket to cylinder block mounting bolts	115	85
Exhaust bypass pipe mounting nuts.	24	18
Exhaust manifold heat shield mounting bolts	10	7
Exhaust manifold mounting nuts	23	17
Exhaust manifold mounting studs	13	10
*+ Elastic blade mounting bolts
Step 1	50	37
Step 2	Another 45°	Another 45°
Step 3	Another 45°	Another 45°
High pressure fuel pump	23	17
High pressure fuel pump pulley mounting nut	50	37
Fuel manifold	23	17
Fuel manifold mounting bracket	23	17
Fuel Rail Line Connections
Step 1 - Connecting the high pressure fuel line to the outlet of one fuel line	15	11
Step 2 - Connecting the high pressure fuel line to the fuel rail	15	11
Step 3 - Connecting the high pressure fuel line to the outlet of one fuel line	30	22
Step 4 - Connecting the high pressure fuel line to the fuel rail	30	22
Fuel manifold high pressure line mounting bolt	10	7
Fuel injector mounting bolts	10	7
Fuel filter mounting bolts	10	7
Generator mounting bolts	23	17
Generator bracket mounting bolts	23	17
Glow plugs	11	8
Bolts for fastening the bracket of the air intake channel air damper elbow	10	7
Knock sensor mounting bolts	20	15
Bolts securing the EGR heat exchanger to the cylinder block	10	7
Upper oil dipstick tube mounting bolt	10	7
Oil pan mounting bolts	10	7
Oil pump mesh and suction tube	10	7
Oil pump mounting bolts to cylinder block	10	7
Oil pan drain plug	23	17
Oil separator bolts	10	7
Oil temperature sensor	10	7
Oil filter	25	18
Piston cooling nozzle mounting bolts	10	7
Power steering bracket mounting bolts	23	17
Power steering pump mounting bolts	23	17
Fastening the high pressure line of the power steering	25	18
Primary tensioner mounting bolts for the timing chain drive	10	7
Secondary timing chain tensioner mounting bolts	10	7
Starter mounting bolts	45	33
Timing chain tensioner bolt	24	18
Timing Belt Tensioner Roller Fastening Bolts	45	33
Transmission Fluid Cooler Tube Bracket	10	7
Gearbox mounting bolts	45	33
Turbocharger heat shield	10	7
Turbocharger bracket	22	16
Coolant pump mounting bolts	10	7
Coolant pump pulley mounting bolts	23	17
Coolant Pump Outlet Pipe Fastening Bolts	10	7
Valve Cover Fastening Bolts	10	7
Vacuum pump mounting bolts	23	17
Vacuum pump mounting nuts	13	10

* Tighten bolts in the sequence shown.
+ Install new bolts
1 Lightly lubricate the bolt threads
2 Do not lubricate the bolt threads